VTech 900I LCD Display, Clocwtime Stamp Display, Base Keypad Functions, Message Counter, Onioff

Page 11

INTEGRATEDTELEPHONEANSWERINGDE@

(ITAD)-OPERATION .

I

-. -

-

-

. - *.- . 2 * _ _ ^ -

^ * - .- . .- ^

LCD DISPLAY

LCD Display Icons

MAILBOX

The MAILBOX icon and the Mailbox Number icons remain on steadily if the ITAD is set-up for 1 or more mailboxes. Otherwisethey remainoff for zero mailboxes. See Mailbox programming.

The Mailbox Number icons flash (in conjunction with MESG'S icon) to indicate new messages designated for specificmailboxes. Newmessages for the Generic mailbox do not cause the MAILBOX icons to flash.

MESG'S

REC

REC (the Record icon) flashes when either of the two outgoing announcements(Announcement1 or 2), or a memo is being recorded.

MEMO

The MEMO icon remains on steadily during memo playback. MEMOalsoremainsonsteadilyduring recording of a memo.

ANNC

The Announcement icon, ANNC, illuminatessteadily inconjunction with one of the Announcement Number icons (1,2 or OGM) to indicate which outgoing announcement has been selected.

ANNC and the corresponding Announcement Number icon also illuminate steadily when the announcement is being recorded.

DAY

The Day icons (SUN-SAT) indicates thecurrent day bysteadily illuminating the correspondingday icon when the ITAD is not in use. If the clock has not been set the SUNday icon will flash. The Dayicon also indicatesthe day a message/memo was recorded by steadilyilluminatingthe corresponding

LCD Display Digits

CLOCWTIME STAMP DISPLAY

The fourdigits onthe leftofthe display, including the colon and the amlpm icons,displaycurrenttimeof daywhen the ITAD is not in use.

If the clock has not been set it will remain flashing until it is properly set (See Time and Day Setup).

Duringmessage/memoplayback,the clock will steadily display the time stamp for that message/memo.

Duringthe recordingof either memos or outgoingannouncements,the clock will display the elapsed time in minutes:seconds.

In the Volume Setting mode, the messagecounter will display an 'L'in the first digit, followed by a 1,2,3,or 4 in the second digit corresponding to the current volume level setting.

BASE KEYPAD FUNCTIONS

lTAD

FUNCTIONS

ON 1 OFF

MESGIS(the Messages icon) flashes to indicate new messages and/or memos.

MESG'S willalways flash if a new message/memo is present, independent of the current mailbox selection.

MESG'Sremains on steadily if there are messages in memory, but no new messages.

day icon for the duration of the message/memo playback.

Allof the Dayiconsflashwhen memory is full.

BATTERY

The Battery icon will flash when the back-up battery is in need of replacement.

This will only function when power is applied to the unit; it will not function when the back-up battery is in use.

MESSAGE COUNTER

 

 

Main Function Keys

 

ONIOFF

w

This key is used to turn ON and OFF

the ITAD. While in the OFF state, the

The two digits on the right hand side

cordless phone will still operate

of the display form the message

normally.

counter. They displaythetotalnumber

When the ITAD is ON, the power LED

of messages (old and new) in the

besidethe ONIOFFkey isilluminated.

current mailbox selection (thedefault

 

selection is All Mailboxes).

 

Page 10 Page 12
Image 11
Page 10 Page 12
Contents UEal Programmi Changing ChannelsChecking the Ringer Main Function KeysBracket Only from the type of power source Outlet before cleaning. Do not useUse a damp cloth for cleaning Product may fall, causing seriousIIT is Impossible to OVER-I Charge the Batteries Case of Difficulty Setting Up Your VTechPulse Charge the Handset Batteries Before USE Connect telephone line cord to base unit and telephone jack Set Dial Mode switch to Pulse orSetting the Mailboxes Volume ControlsSetting the Ring Type Setting the Security CodeTurning Off The Ringer Changing ChannelsTemporary,Tone Programming the Ringer TypeMEM PHONE, MEMMessage Counter LCD DisplayClocwtime Stamp Display Base Keypad FunctionsMemory VolumeSetup MemoType programming mode Advance to security Code To change ring type settingCurrent mode of operation and return Recording, or exit the set-up modeGeneric mailbox is enabled To change security code Press and hold Setup until it beepsPress Setup to exit timelday Storage. On initial power-up, onlyListening t o Messages Example for AnnouncementLeaving a Message Speak into the base microphone to record the memoTo activate remote operation from a different telephone line Followed by $Recording a Memo Voice PromptsListeningto Messages Changingthe AnnouncementLeaving Memos This key has no function if ITADis not in Playback modeDepending on the current announcement selection Taking Care of Your Telephone Select AnnouncementRecord Memo # OFFOUT of Range Indication OUT of Range When Phone is onOUT of Range When Phone is OFF Noise or InterferenceHOW do I Send MY UNIT, in or OUT of WARRANTY? Handset does not Ring When YOU Receive a CallYOU Hear Other Calls While Using Your Phone What does OUR Warranty COVER?Increase the separation between the equipment and receiver Reorient or relocate the receiving antennaVtech Communications Vtech ElectronicsTransmit Frequency WeightPower Requirements Frequency ControlVtech Cordless Telephone Wall Mounting Template
Top Page Image Contents