VTech 900I To change security code Press and hold Setup until it beeps, Programming. Use Repeat

Page 14

To change security code:

1.Press and hold SETUP until it beeps.

2.Press SETUP briefly. The LCD will display "SC" (Security Code) and the current security code setting.

3.Use REPEATand SKlP to scroll to desired code, between 00 and 99.

4.Press SETUP to exit security code programming mode, and advance

to timelday- programming,. - - or.press STOP to exit.

SECURITY CODE

SElTlNG

g#jxi:

1

Bl %4

1

aor

To change the time display on the LCD:

1.Press and hold SETUP for 2 seconds or until it beeps.

2.Press SETUP 2 times until clock is displayed and the DAY icon is flashing.

3.Use REPEAT and SKlP keys to select correct day.

4.Press SETUP to advance to hour programming. Use REPEAT and SKlP keys to select correct hour and amlpm.

To change the number of mailboxes:

1.Press and hold SETUP for 2 seconds or until it beeps.

2.Press SETUP 5 times until MAILBOX icon is illuminated.

3.Use REPEAT and SKlP keys to scroll through selections (the Mailbox Number icons indicate which mailboxes are enabled).

4.Press SETUP to exit mailbox programming mode, and return to

ring type programming, or press STOP to exit.-

MAILBOX

PROGRAMMING

:%

4

~s

1

or

1

Announcement 2

You can record your own announcement butthecaller is notable to leave a message.

If you do not record your own announcement, the factory default announcement:

No one can answer the phone at the moment, please call again.

will be used (see Recording the Announcement ).

After you record your own announcement, you can return to the default announcement by record an OGM less than 1 second.

OGM (OutGoing Message)

You are not able to record an announcement, it is programmed into ITAD memory. The caller is not able to leave a message.

Programmed OGM Announcement: No one can answer the phone at the moment, please call again.

Note: The ITAD will default to OGM Announcement if the current

INote: , When accessing the ITADI remotely,the securitycode ispreceded by the * key.

Time and Day Setup

The Time and Daydefault is set to SUN 12:OO pm. This will flash to indicate clock has not been set.

5. Press SETUPto advanceto minute

 

Selecting the Announcement

programming. Use REPEAT and

 

 

The ANNC key is used to select the

SKlP keys again.

 

 

 

 

currentoutgoingannouncement.There

 

 

 

6. Press SETUP to exit timelday

 

are 3 choices of Announcements as

 

follows: 1, 2 & OGM.

programming mode, and advance

 

 

 

to mailbox programming, or press

1

Announcement 1

STOP to exit.

 

 

YOUcan record your own personal

Mailbox programming

 

 

announcementand the caller is able to

 

 

leave a message.

The ITAD has the ability to be

 

 

If you do not record your own

programmed for up to

4 individual

 

 

announcement, the factory default

 

 

 

mailboxes. In addition, there is also a

announcement:

Generic mailboxfor general messages

Please record message after the

storage. On initial power-up, only the

tone.

Generic mailbox is enabled.

will be used (see Recording the

 

 

Announcement).

selection is Announcement 1 and the memory is full.

Recording the Announcement 1 . Press ANNC key until the desired announcement icon is displayed on the screen (1 or

2 ) .

2. Press and hold ANNC key for 2 seconds until a beep is heard. The clock will display 0:00 and will start incrementing for the length of the announcement.

Page 13 Page 15
Image 14
Page 13 Page 15
Contents UEal Main Function Keys Changing ChannelsChecking the Ringer ProgrammiBracket Product may fall, causing serious Outlet before cleaning. Do not useUse a damp cloth for cleaning Only from the type of power sourceIIT is Impossible to OVER-I Charge the Batteries Case of Difficulty Setting Up Your VTechPulse Charge the Handset Batteries Before USE Set Dial Mode switch to Pulse or Connect telephone line cord to base unit and telephone jackSetting the Security Code Volume ControlsSetting the Ring Type Setting the MailboxesProgramming the Ringer Type Changing ChannelsTemporary,Tone Turning Off The RingerPHONE, MEM MEMBase Keypad Functions LCD DisplayClocwtime Stamp Display Message CounterMemo VolumeSetup MemoryRecording, or exit the set-up mode To change ring type settingCurrent mode of operation and return Type programming mode Advance to security CodeStorage. On initial power-up, only To change security code Press and hold Setup until it beepsPress Setup to exit timelday Generic mailbox is enabledSpeak into the base microphone to record the memo Example for AnnouncementLeaving a Message Listening t o MessagesFollowed by $ To activate remote operation from a different telephone lineChangingthe Announcement Voice PromptsListeningto Messages Recording a MemoLeaving Memos This key has no function if ITADis not in Playback modeDepending on the current announcement selection # OFF Select AnnouncementRecord Memo Taking Care of Your TelephoneNoise or Interference OUT of Range When Phone is onOUT of Range When Phone is OFF OUT of Range IndicationWhat does OUR Warranty COVER? Handset does not Ring When YOU Receive a CallYOU Hear Other Calls While Using Your Phone HOW do I Send MY UNIT, in or OUT of WARRANTY?Vtech Electronics Reorient or relocate the receiving antennaVtech Communications Increase the separation between the equipment and receiverFrequency Control WeightPower Requirements Transmit FrequencyVtech Cordless Telephone Wall Mounting Template
Top Page Image Contents