VTech 900I Frequency Control, Transmit Frequency, Receive Frequency, Nominal Effective Range

Page 23

IC (Industry Canada)

This telephone is registered for use in Canada.

Notice: The lndustry Canada label identifies certified equipment. This certificationmeans that the equipment meets certain telecommunications network, protective, operational and safety requirements, lndustry Canada does not guarantee the equipment will operate to the user'ssatisfaction.

Before installingthis equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company. The equipment must also be installed using an acceptable method of connections. The customer should be aware that compliance with the above conditionsmay not preventdegradation of service in some situations.

Repairs to certified equipment should be made by an authorized Canadian maintenancefacility designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunicationscompanycauseto request the user to disconnect the equipment.

Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines and internal metallic water pipe system, if present, are connected together. This precaution may be particularly important in rural areas.

Caution: Users should not attempt to make such connections themselves, but should contact the appropriate electric inspection authority, or electrician, as appropriate.

The LoadNumber (LN)assignedto this device denotes the percentage of the total loadto beconnectedto atelephone loop which is used by the device to prevent overloading. The termination on a loop may consist of any combination of devices subject only to the requirement that the total of the load numbers of all the devices does not exceed 100.

This device complies with RSS-210of lndustry Canada. Operation is subject to the following two conditions: (1) this device may not cause interference,and

(2)this device must accept any interference,includingintederencethat may cause undesired operation of the device.

FREQUENCY CONTROL

Crystal Controlled Dual PLL Synthesizer

TRANSMIT FREQUENCY

Handset : 925.05MHzto927.75 MHz (Allten channelswithinthis range)

Base : 902.3 MHz to 905.0 MHz (Alltenchannelswithinthis range)

RECEIVE FREQUENCY

Handset : 902.3 MHz to 905.0 MHz (Allten channelswithinthis range)

Base : 925.05MHzto927.75 MHz (Allten channelswithinthis range)

NOMINAL EFFECTIVE RANGE

Maximum power allowed by FCC and IC. Actual operating range may vary according to environmental conditions at the time of use.

The range quoted for this phone is based on open field measurements under W condmms.

WEIGHT

Handset : 345 grams (with battery)

Base : 1075 grams(with AC adapter)

SIZE

Handset : 20.0cm x 6.2cm x 4.3cm (L x W x T) maximum (antenna excluded)

Base : 22.0cm x 19.5cm x 6.lcm (L x W x T) maximum (antenna excluded)

POWER REQUIREMENTS

Handset : Self-contained nickel- cadmium rechargeable battery supply, 6.OV

nominal, 6OOmAh capacity.

Power Adapter12VDCQ500mA

AND MAY CHANGE WITHOUT NOTICE.

Page 22 Page 24
Image 23
Page 22 Page 24
Contents UEal Programmi Changing ChannelsChecking the Ringer Main Function KeysBracket Only from the type of power source Outlet before cleaning. Do not useUse a damp cloth for cleaning Product may fall, causing seriousIIT is Impossible to OVER-I Charge the Batteries Case of Difficulty Setting Up Your VTechPulse Charge the Handset Batteries Before USE Connect telephone line cord to base unit and telephone jack Set Dial Mode switch to Pulse orSetting the Mailboxes Volume ControlsSetting the Ring Type Setting the Security CodeTurning Off The Ringer Changing ChannelsTemporary,Tone Programming the Ringer TypeMEM PHONE, MEMMessage Counter LCD DisplayClocwtime Stamp Display Base Keypad FunctionsMemory VolumeSetup MemoType programming mode Advance to security Code To change ring type settingCurrent mode of operation and return Recording, or exit the set-up modeGeneric mailbox is enabled To change security code Press and hold Setup until it beepsPress Setup to exit timelday Storage. On initial power-up, onlyListening t o Messages Example for AnnouncementLeaving a Message Speak into the base microphone to record the memoTo activate remote operation from a different telephone line Followed by $Recording a Memo Voice PromptsListeningto Messages Changingthe AnnouncementLeaving Memos This key has no function if ITADis not in Playback modeDepending on the current announcement selection Taking Care of Your Telephone Select AnnouncementRecord Memo # OFFOUT of Range Indication OUT of Range When Phone is onOUT of Range When Phone is OFF Noise or InterferenceHOW do I Send MY UNIT, in or OUT of WARRANTY? Handset does not Ring When YOU Receive a CallYOU Hear Other Calls While Using Your Phone What does OUR Warranty COVER?Increase the separation between the equipment and receiver Reorient or relocate the receiving antennaVtech Communications Vtech ElectronicsTransmit Frequency WeightPower Requirements Frequency ControlVtech Cordless Telephone Wall Mounting Template
Top Page Image Contents