VTech 900I manual Setting Up Your VTech, Pulse Charge the Handset Batteries Before USE

Page 6

Setting Up Your VTech 900i

1.Choose an area near an electrical outlet and a telephone wall jack.

ACTELEPHONE

ELECTRICAL WALL

OUTLETJACK

2. Install optional 9V back-up battery

in compartment located on

underside of 900i base unit. This

batteryretainsmemory inthe event

of a power outage. VTech

recommendsthe use of an alkaline

4.Plug the AC power adapter into an electrical outlet. The ONlOFF LED will flash during initialization for about20seconds. After initialization of the ITAD, the LCD clock display will flash until it is set.

NOTE: Connect power to the base unit beforeplacingthe handsetinthe cradle.

4.Set the TONUPULSE switch on the base unit. If you have touch tone serviceon your phone line,set the switch to TONE. If you have rotary service, set the switch to

PULSE.

I

6. CHARGE THE HANDSET BATTERIES BEFORE USE.

The batteries recharge automaticallywheneverthehandset is in the base unit cradle. The batteries must be charged for 24 hours before using your phone for the first time. The CHARGE LED will flash until the handset is laced in the base cradle and the batteries are charged.

7.CHECK FOR A DIAL TONE. Afterthe batteriesare charged, pick up the handset and press the PHONEkey. The PHONEindicator should light up, and you should hear a dial tone. If not, see IN

CASE OF DIFFICULTY.

CAUTION:

1.Neverinstalltelephonewiringduring a lightning storm.

2.Neverinstalltelephonejacks inwet locations unless the jack is specifically designed for wet locations.

3.Nevertouch uninsulatedtelephone wires or terminals unless the

telephone line has been disconnected at the network interface.

4.Use caution when installing or modifying telephone lines.

battery.

3.Connect the telephone line cord. Insertone end of the telephone line cord into the jack at the rear of the base unit. Plugthe other end into a telephone wall jack. Make sure the plugs snap securely into place.

5.Fill in the telephone number card on the base unit.

CHECK

FOR A

DlAL TONE

Page 5 Page 7
Image 6
Page 5 Page 7
Contents UEal Main Function Keys Changing ChannelsChecking the Ringer ProgrammiBracket Product may fall, causing serious Outlet before cleaning. Do not useUse a damp cloth for cleaning Only from the type of power sourceIIT is Impossible to OVER-I Charge the Batteries Setting Up Your VTech Pulse Charge the Handset Batteries Before USECase of Difficulty Set Dial Mode switch to Pulse or Connect telephone line cord to base unit and telephone jackSetting the Security Code Volume ControlsSetting the Ring Type Setting the MailboxesProgramming the Ringer Type Changing ChannelsTemporary,Tone Turning Off The RingerPHONE, MEM MEMBase Keypad Functions LCD DisplayClocwtime Stamp Display Message CounterMemo VolumeSetup MemoryRecording, or exit the set-up mode To change ring type settingCurrent mode of operation and return Type programming mode Advance to security CodeStorage. On initial power-up, only To change security code Press and hold Setup until it beepsPress Setup to exit timelday Generic mailbox is enabledSpeak into the base microphone to record the memo Example for AnnouncementLeaving a Message Listening t o MessagesFollowed by $ To activate remote operation from a different telephone lineChangingthe Announcement Voice PromptsListeningto Messages Recording a MemoThis key has no function if ITADis not in Playback mode Depending on the current announcement selectionLeaving Memos # OFF Select AnnouncementRecord Memo Taking Care of Your TelephoneNoise or Interference OUT of Range When Phone is onOUT of Range When Phone is OFF OUT of Range IndicationWhat does OUR Warranty COVER? Handset does not Ring When YOU Receive a CallYOU Hear Other Calls While Using Your Phone HOW do I Send MY UNIT, in or OUT of WARRANTY?Vtech Electronics Reorient or relocate the receiving antennaVtech Communications Increase the separation between the equipment and receiverFrequency Control WeightPower Requirements Transmit FrequencyVtech Cordless Telephone Wall Mounting Template
Top Page Image Contents