Grandstream Networks GXP1100/1105 manual Name DNS Mode Primary IP Backup IP, Local SIP Port

Page 22

Name

DNS Mode

Primary IP

Backup IP 1

Backup IP 2

TEL URL

SIP Registration

Unregister on Reboot

Register Expiration

SIP service subscriber’s name that is used for Caller ID display.

The default is set to A Record. If user wishes to locate the server by DNS SRV, the user may select SRV or NATPTR/SRV. When "Use Configured IP" option is selected, if SIP server is configured as domain name, phone will not send DNS query, but use "Primary IP" or "Secondary IP" to send sip message if at least one of them are not empty.

This option applies only if “Use Configured IP” is selected, the phone will send DNS query to the Primary IP. Insert IP address here.

Insert the first back up IP here.

Insert the second back up IP here.

Select Tel URI as “Disabled”, “User=Phone” or “Enabled”. Default is “Disabled”.

This parameter controls sending REGISTER messages to the proxy server. The default setting is “Yes”.

Default is “No”. If set to “Yes”, the SIP user’s registration information will be cleared on reboot.

This parameter allows user to specify the time frequency (in minutes) that GXP1100/1105 refreshes its registration with the specified registrar. The default interval is 60 minutes. The maximum interval is 65,535 minutes (about 45 days).

Local SIP Port

SIP Registration Failure Retry Wait Time

SIP T1 Timeout

SIP T2 Interval

SIP Transport

Check Domain

Certificate

Remove OBP from Route

Validate Incoming Messages

Support SIP Instance ID

This parameter defines the local SIP port used to listen and transmit. The default value for Account 1 is 5060. It is 5062, 5064, 5066 for Account 2, Account 3 and Account 4 respectively.

Retry registration if the process failed. Default is 20 seconds.

RFC 3261 SIP T1 timer. Default is 0.5 second.

RFC 3261 SIP T2 timer. Default is 4 seconds.

Choose SIP Transport between UDP and TCP. Default is UDP.

Enable to check the domain certificate. Default is “No”.

The SIP Extension notifies the SIP server that it is behind a NAT/firewall.

This configuration selects whether or not the incoming messages should be validated.

Selects whether or not SIP Instance ID is supported.

Grandstream Networks, Inc.

GXP1100/1105 User Manual

Page 21 of 29

 

Firmware version: 1.0.1.80

Last Updated: 07/2011

Image 22
Contents Grandstream Networks, Inc Table of Contents GUI Interface Examples Welcome GXP1100/1105 Connectors InstallationEquipment Packaging GXP1100/1105 Hardware Specifications GXP1100/1105 Feature GuideGXP1100/1105 Key Features in a Glance Product OverviewGXP1100/1105 Technical Specifications Firmware UpgradesSecurity Completing Calls Using the GXP1100/1105Call Appearance with 1 SIP Account GXP1100/1105 Keypad ButtonsMaking Calls using IP Addresses Mute Receiving CallsCall Waiting/Call Hold Call TransferVoice Messages Message Waiting Indicator GXP1100/1105 Call FeaturesConfiguration Guide GXP1100/1105 IVR Menu DefinitionsAccess the Web Configuration Menu DefinitionsDevice Configuration Status Device Configuration Settings/Basic SettingsDevice Configuration Settings /Advanced Settings HTTP/HTTPS Password Firmware UpgradeXML Config File Upgrade ViaEnable TR-069 Automatic UpgradeAuthenticate Conf File TR-069 PasswordSend SIP Log Password Distinctive Ring ToneSyslog Level NTP serverWaiting Tone Disable Direct IP Calls Disable Call WaitingDisable Call Use Quick IP Call ModeSIP Account Settings Display LanguageLocal SIP Port Name DNS Mode Primary IP Backup IPSIP Registration Unregister on Reboot Register Expiration Support SIP Instance IDFirmware version Last Updated 07/2011 Firmware version Last Updated 07/2011 Firmware version Last Updated 07/2011 Firmware version Last Updated 07/2011 ILBC Frame Size ILBC Payload Type Special Feature IVR Menu Software Upgrade & CustomizationWeb Configuration Interface No Local TFTP/HTTP ServerInstructions for Local Tftp Upgrade Managing Firmware and Configuration File DownloadRestore Factory Default Setting Instructions for Restoration