Cisco Systems AS5800 manual Command History, Router# show voice port 1/0/0

Page 38

Command Reference

Command History

Release

Modification

11.3(1)T

This command was introduced.

 

 

11.3 MA

Port-specific values for the Cisco MC3810 were added.

 

 

12.0(3)T

Port-specific values for the Cisco AS5300 were added.

 

 

12.0(7)T

Port-specific values for the Cisco AS5800 were added.

 

 

Usage Guidelines

This command applies to Voice over IP, Voice over Frame Relay, Voice over ATM, and Voice over HDLC.

Use the show voice port privileged EXEC command to display configuration and voice interface card-specific information about a specific port.

Examples

The following is sample output from the show voice port command for an E&M voice port on the Cisco 3600 series:

router# show voice port 1/0/0

E&M Slot is 1, Sub-unit is 0, Port is 0

Type of VoicePort is E&M

Operation State is unknown

Administrative State is unknown

The Interface Down Failure Cause is 0

Alias is NULL

Noise Regeneration is disabled

Non Linear Processing is disabled

Music On Hold Threshold is Set to 0 dBm

In Gain is Set to 0 dB

Out Attenuation is Set to 0 dB

Echo Cancellation is disabled

Echo Cancel Coverage is set to 16ms

Connection Mode is Normal

Connection Number is

Initial Time Out is set to 0 s

Interdigit Time Out is set to 0 s

Analog Info Follows:

Region Tone is set for northamerica

Currently processing none

Maintenance Mode Set to None (not in mtc mode)

Number of signaling protocol errors are 0

Voice card specific Info Follows:

Signal Type is wink-start

Operation Type is 2-wire

Impedance is set to 600r Ohm

E&M Type is unknown

Dial Type is dtmf

In Seizure is inactive

Out Seizure is inactive

Digit Duration Timing is set to 0 ms

InterDigit Duration Timing is set to 0 ms

Pulse Rate Timing is set to 0 pulses/second

InterDigit Pulse Duration Timing is set to 0 ms

Clear Wait Duration Timing is set to 0 ms

Wink Wait Duration Timing is set to 0 ms

38Cisco IOS Release 12.0(7)T

Image 38
Contents Feature Overview Voice over IP for the Cisco AS5800Two-Stage-Dial Toll Bypass Feature OverviewBenefits Pstn Voice-Traffic and Fax-Traffic Off load Benefits Two-Stage Dial Toll BypassRestrictions Related Features and TechnologiesUniversally Accessible Voice-Mail and Fax-Mail Services Related DocumentsStandards Supported PlatformsSupported Standards, MIBs, and RFCs MIBsPrerequisites PrerequisitesConfiguration Tasks Configuration TasksConfiguring IP Networks for Real-Time Voice Traffic Configuring Voice Ports Configuring Custom Queuing and IP RTP ReserveConfiguring Voice Ports Step Command PurposeFine-Tuning Isdn Voice Ports Configuration Tasks Step Command PurposeSecondsinfinity Verifying Voice Port ConfigurationTroubleshooting Tips Configuring Dial Peers Inbound versus Outbound Dial PeersOutbound Dialing on Pots Peers Configuring Pots PeersPots command is a tag that uniquely identifies Pots peer. The number value of the dial-peer voiceDirect Inward Dial for Pots Peers Incoming and Outgoing Pots Call LegsUsing the elements, the algorithm is as follows Distinguishing Voice and Modem Calls on the Cisco AS5800Configuring VoIP Peers Verifying Dial Peer ConfigurationRouterconfig-if#h323-gateway voip interface Configuring the Cisco AS5800 as an H.323 GatewayConfiguring the Cisco AS5800 as an H.323 Gateway Routerconfig-if#h323-gateway voip h323-idConfiguring IVR Configuring the Cisco AS5800 for Interactive Voice ResponseVerifying Gateway Interface Configuration Router config# call application voice nameConfiguration Example Configuration ExampleVerifying IVR Configuration Configuring the Cisco AS5800 as a Gateway Configuring the Cisco 3640 as a GatekeeperConfiguring the Cisco 2600 as a Gateway Command Reference Command ReferenceNew Commands Modified Commands Codec Port Show csm Show voice port Voice-portCodec DefaultsCommand Modes Syntax DescriptionUsage Guidelines Command HistoryRelated Commands ExamplesDtmf-relay CommandDescription Port DefaultNo port is configured Cisco MC3810Command Mode ExampleShow csm Router# show csm voice 2/4/4/0 Show csm voice Field Descriptions Explains the fields contained in both of these examplesSpecifies the T1 or E1 controller Field DescriptionCommand Reference Show csm voice Field Descriptions Show csm Tdmdspstream Related Commands Show voice port Syntax Description For the Cisco 2600/3600 seriesFor the Cisco MC3810 For the Cisco AS5300 Access ServerFor the Cisco AS5800 Universal Access Server Show voice portRouter# show voice port 1/0/0 Router# show voice port 1/2 Summary Explains the fields in the sample outputShow voice port Field Descriptions Show voice port 5800# show voice port 1/0/0D Isdn 1/0/0D Command Reference Show voice port Field DescriptionsShow voice port Field Descriptions for the Cisco AS5800 Show call active voice 5800# show vrm activecalls Show vrm activecallsReleaseModification Show vrm activecalls Show vrm vdevice Field DescriptionsCommand Reference Show vrm vdevice Field Descriptions Show vrm vdevices Show vrm vdevices5800# show vrm vdevices 6 Show vrm vdevices 5800# show vrm vdevices summary Summary of voice devices for all voice cardsShow vrm vdevice summary Field Descriptions CCCAPCODECG711U DSP# Show vrm activecalls Router# test vrm busyout 4 all Test vrm busyoutTest vrm busyout Router# test vrm busyout 4 1 Router# test vrm busyout 4 1 channelTest vrm reset Test vrm resetFollowing example resets DSP 4 on the VFC installed in slot Router# test vrm reset 4Test vrm unbusyout Router# test vrm unbusyout 4 allRouter# test vrm unbusyout 4 1 channel Test vrm unbusyoutRouter# test vrm unbusyout 4 1 Voice-port Global configuration Voice-portDial-peer voice Debug Commands Debug CommandsNew Debug Commands There are no arguments or keywords used in this command Debug vrm controlDebug vrm control Format of the Send messages is as followsFormat for the Receive messages is as follows Describes the fields in previous example Debug vrm control Field DescriptionsDebug vrm error Debug vrm errorVtspfail codec value not supported Debug vrm error Field Descriptions This error message notifies the VRM of a DSP alarmPossible state values are as follows = Reset Expains the field contained in the previous exampleDebug vrm control Debug vrm inout Debug vrm inoutGlossary GlossaryGlossary Glossary
Related manuals
Manual 168 pages 22.1 Kb Manual 6 pages 32.91 Kb Manual 16 pages 55 Kb

AS5800 specifications

Cisco Systems has long been a leader in the networking and telecommunications field, and its AS5800 series of routers exemplify this tradition. The AS5800, along with the AS5850, AS5350, AS5400, and AS5300, provides robust solutions for service providers and enterprise-level networking applications. Each of these models has distinct features and characteristics that cater to the evolving demands of internet traffic and data processing.

The Cisco AS5800 is designed for high-capacity routing and optimized for broadband services. It supports a wide range of services, including voice, data, and video applications, making it a versatile option for service providers looking to deliver integrated solutions. It is equipped with advanced quality of service (QoS) features that ensure bandwidth is allocated effectively, holding strong even under heavy traffic conditions.

In comparison, the AS5850 offers superior processing capabilities and is typically utilized in larger-scale implementations. This model supports high-density interfaces, allowing numerous connections without compromising performance. Its architecture includes enhanced MPLS (Multiprotocol Label Switching) support, enabling more efficient traffic management and better utilization of network resources.

The AS5350 is known for its scalability and energy efficiency, ideal for voice-over-IP (VoIP) and media gateway applications. It supports various telephony features, such as protocol interworking and transcoding, making it a preferred choice for organizations focusing on digital voice technologies. The AS5300, while slightly older, continues to be a valuable asset for less demanding networks, offering reliable performance with VoIP capabilities and basic data applications.

The AS5400 bridges the gap between high-performance routing and operational efficiency. It incorporates Cisco's proprietary technologies to ensure seamless connectivity and robust failover systems. This model is highly regarded for its security features, protecting network integrity and providing peace of mind for businesses relying on sensitive data transfer.

Overall, Cisco’s AS5800 series showcases a progressive evolution of routing capabilities with enhanced features tailored for resilience, scalability, and performance. These routers not only address the technical needs of modern networks but also strategically position organizations for future growth in an increasingly digital world. Each model, with its unique attributes, continues to support the varied demands of global communication infrastructures.