AT&T E2126, E1126 user manual Can’T

Page 43

Appendix

Troubleshooting

My cordless handset beeps five times and isn’t performing normally.

•Make sure the power cord is securely plugged into the base. Plug the unit into a different, working electrical outlet not controlled by a wall switch.

•Move the cordless handset closer to the base. You might have moved out of range.

•Reset the base. Unplug the unit’s electrical power. Wait for 15 sec- onds then plug it back in. Allow up to one minute for the cordless handset and base to reset.

•Other electronic products can cause interference to your cordless phone. Try installing your phone as far away from these types of electronic devices as possible: wireless routers, radios, radio towers, pager towers, cell phones, intercoms, room monitors, televisions, personal computers, kitchen appliances and other cordless phones.

CAN’T

CONNECT displays on my cordless hand- set.

•Move the cordless handset closer to the base. You might have moved out of range.

•Ensure that the base is powered up.

•Place the cordless handset in base cradle for 1 minute to allow the cordless handset and base to resynchronize channels.

•If the cordless handset is in its base and the charging light does not come on, refer to the charge light is off in this troubleshooting guide.

•Reset the base. Unplug the unit’s electrical power. Wait for 15 seconds then plug it back in. Allow up to one minute for the cordless handset and base to reset.

•Other electronic products can cause interference with your cordless phone. Try installing your phone as far away from these types of elec tronic devices as possible: wireless routers, radios, radio towers, page towers, cell phones, intercoms, room monitors, televisions, personal computers, kitchen appliances and cordless phones.

The batteries will not hold a charge.

•Charge the battery in the cordless handset for at least 16 hours. For optimum daily performance, return the cordless handset to its base when not in use.

•Ensure that the battery is properly installed and charged as described on page 7.

•Ensure that the telephone base and charger units are plugged into functioning power outlets.

•If your battery is old, you may need to purchase a new battery pack, see page 7.

•Your phone might be malfunctioning. Please refer to the Warranty section of this user’s manual for further instruction.

•If the cordless handset is in its base and the charging light does not

come on, refer to “The charge light is off” in this troubleshooting guide.

39

Page 42 Page 44
Image 43
Page 42 Page 44
Contents GHz Cordless Telephone/Answering System E2126/E1126 Need HELP? Information about Caller ID with Call Waiting See System E2126/E1126 Table of contentsPress to display last number called see Quick reference guideDate Time During a call, press to mute microphone seePlaying messages Telephone BaseTelephone base Parts checklistTelephone Operating Range Battery Pack for Cordless HandsetBefore you begin Caller ID and Call WaitingTelephone base installation Press down on tab to open the battery door Battery installation & chargingIs low Plug telephone line cord into telephone cord wall jack Wall mountingBelt clip & optional headset Install belt clip as shown below if desiredChoose cordless handset ringer sound Choose cordless handset ringer volumeSet cordless handset display date and time Clear Voice Mail for all cordless handsets Choose dial modeChoose cordless handset display language Last number redial Basic cordless handset operationMaking and answering calls Hands-free speakerphone callsHandset Locator Base operationHandset Locator does not generate any paging tone Options while on calls Speed dialing Memory capacityTo edit or delete a Speed Dial number Speed dialingTo enter a Speed Dial number To call a Speed Dial numberTo enter a name Entering names into directoryTo assign a distinctive ring Entering numbers into directoryTo enter a number Options while entering numbersTo call a displayed number Directory searchTo browse through the directory To search alphabeticallyTo make an entry into a Speed Dial entry Changing directory entriesTo edit an entry To delete an entryHow Caller ID works On-Screen Message Reason About namesMissed calls Other options To review your call logTo review your call log To return a callNumber displayed as To dial a call log entryDialing options ExampleCall log cleared To delete call log entriesTo delete a single call log entry To delete all call log entriesEntry added to phone directory To add entries to phone directoryEdit name as desired Edit number as desiredSee Press to review or set clock see Setup option seeMessage capacity Message window Number of messagesTo check day and time Clock settingDay and time announcements To set day and timeTo record your outgoing announcement Outgoing announcementsTo delete your outgoing announcement To turn Announcement Only on or off Announcement Only modeOption selected Feature options Changing feature optionsDisabling the message alert function temporarily To delete all messages Message playbackAnnouncements Options during playbackTo record a memo Recording and playing memosTo play back a memo Message counter displays Message window displaysMessage window Remote access Screen display messages Display screen messages, lights and tonesAlert tones Indicator lightsMy phone doesn’t work at all TroubleshootingCAN’T Hear other calls while using my phone Hear noise Charge light is off Incomplete Important Safety Instructions Especially About Cordless Telephones Pacemaker Patients Precautions for Users of Implanted Cardiac PacemakersFCC Part 68 and Acta FCC Part What does this limited warranty cover? Limited WarrantyLimited Warranty Please retain your receipt as your proof of purchase Technical specifications Index Cut along dotted line Remote access wallet cardFold here
Top Page Image Contents