AT&T Door Phone Controller Installation, Mounting Instructions, Wall Mount Instructions

Page 27

Installation

Mounting Instructions

The AT&T Door Phone Controller can be placed on a flat table or shelf, or mounted to a wall.

Wall Mount Instructions

When moving AT&T Door Phone Controller or adding/ removing cables from back panel, unplug transformer from 120V outlet.

Also unplug the terminal strip and modular phone connectors on the back panel.

The AT&T Door Phone Controller is shipped with a keyhole mounting template and mounting screws. Follow the steps below to mount the Door Phone Controller to a wall.

1.Place template (tear-out page at end of manual) over desired wall mounting location and mark screw positions.

2.Use a Philips screwdriver to screw each of the two screws into the marked screw positions.

IMPORTANT: Do not drive screws all the way into wall; adequate space (5/16'') must be left to position the AT&T Door Phone Controller bottom panel keyholes over screw heads.

3.Mount the AT&T Door Phone Controller over the protrud- ing screw heads and seat unit firmly to the wall. See Figure 2-3.

WARNING: RISK OF ELECTRICAL SHOCK — EQUIPMENT MUST BE PROPERLY GROUNDED. Your AT&T equipment requires a properly grounded three-prong power receptacle for safe operation. Have the receptacle checked by a qualified electrician before connecting this equipment. Do not cut or remove the third (ground) prong from the power transformer. Do not use two-prong extension cords or adapters to defeat the safety features of this equipment. If you have a two-prong receptacle, it must be replaced with a three-prong receptacle, installed by a qualified electrician.

Installation Procedures

2-11

Page 26 Page 28
Image 27
Page 26 Page 28
Contents AT&T Compatibility Plus AT&T Door Phone Controller Compatibility ChartApplication Notes for Compatibility Chart Application Notes for Compatibility Chart Contents Troubleshooting and Maintenance Page Figures Page Tables Introduction Using This Manual AT&T Door Phone Controller FeaturesSpeaker Volume Talk Back DIP Switch LED PBX Private Branch Exchange -Business telephone Terms You Should KnowInstallation Procedures Installation Procedures Important Safety Instructions Page General Information Door Phone Controller Back Panel Connections IntroductionPage Door Phone Controller Back Panel Connections Prior To InstallationAT&T Door Phone Controller Location Typical AT&T Door Phone Controller Installation Installation Mounting InstructionsWall Mount Instructions Mounting AT&T Door Phone Controller to Wall Remote Door Open Switch optional SHIELDED, Twisted PAIR, 24 AWG Electric Door Strike Plate Device optional Connections for Remote Door Open Switch optionalConnections for Electric Door Strike Plate optional Auxiliary Alert Device optional Connecting PowerConnections for Auxiliary Alert Device optional Installation Procedures Door Ajar Function Speaker Volume ControlTalk Back Volume Control Operation and Controls InformationLED Configuration of Telephone Equipment Flow Chart Installation Home/Residential Overview DIP Switch SelectionsHome/Residential DIP Switch Settings AT&T Door Phone Controller Back Panel Option Selection AT&T Door Phone Controller Option Selection Information Operation Basic Door Answer Function Visitor Presses Door Speaker ButtonAnswering a Call from the Door Speaker Calling the Door Speaker from Inside the Building Telephone Line In Use With Door When Incoming Call Arrives Installation Dedicated Trunk Port Overview DIP Switch Setting for PBX with Dedicated Trunk Port Telephone System 2b. Ground Start Installations Option Selection Page Options Mode Option Press Listen Default Verify For Calling the Door Speaker Installation for PBX Equipment With Available Station Port Overview G E ND Telephone System Option Selection Page Options Mode Option Listen Press Default Verify For Auxiliary Alert Mode Basic Door Answer Function Ringdown Mode Basic Door Answer FunctionOperation Opening door will terminate station mode access Installation No Dedicated Trunk/Station Port DIP Switch Selections DIP Switch Setting for PBX With Shared Trunk Port AT&T Door Phone Controller Back Panel Option Selection Port Saver Mode Port Saver or Trunk Saver Mode InstallationTrunk Saver Mode Delay Operation Basic Door Answer Function Calling the Door Speaker From Inside the Building Placing a Call Through the C.O. From Inside Building Telephone Line In Use With Door When a Call ArrivesTroubleshooting and Maintenance Troubleshooting Procedures Troubleshooting ProceduresWhen door ajar switch is not Operating as Expected MaintenanceSetting the DIP Switch Positions Appendix A-DIP Switch SettingsNot used Ring/Chime Cadence Ring/Chime Duration Appendix B-Option Selection Mode DefinitionsPage Electrical Appendix C-SpecificationsRing Generator Line Jack MechanicalInstallation Information Using With an Answering Machine Appendix E-Auxiliary Alert Option Installation InstructionsPage Figure E-1. Connections For Auxiliary Alert Device FCC Part FCC Regulations and Warranty Limited Warranty and Limitation of Liability Warranty InformationFCC Regulations and Warranty Memory AT&T Door Phone Controller Option SelectionDoor Phone Controller DIP Switch Settings1992 AT&T CIC# 0II722050-055 Issue 3, November

Door Phone Controller specifications

The AT&T Door Phone Controller is a cutting-edge device designed to enhance home security and communication. This innovative system seamlessly integrates with a home's existing telephone network, allowing users to monitor and communicate with visitors at their door without needing to install a separate intercom system. With its user-friendly interface and advanced features, the AT&T Door Phone Controller is a valuable addition to any modern home.

One of the standout features of the AT&T Door Phone Controller is its ability to connect with a standard telephone line. This means homeowners can answer their door from anywhere in the house, using their existing landline phones or cordless handsets. The device is equipped with a high-quality speaker and microphone, ensuring clear two-way communication. This is particularly useful for homeowners who may not always be near the front door or those who wish to maintain their privacy by not opening the door to strangers.

In terms of technology, the AT&T Door Phone Controller utilizes a reliable digital signal processing system that enhances audio clarity and reduces background noise. This ensures that every conversation is heard loud and clear, even in noisy environments. The device also features adjustable volume levels, allowing users to customize the audio output according to their preferences.

Another significant characteristic of the AT&T Door Phone Controller is its built-in video capability. Some models come equipped with a camera that provides a live video feed of the person at the door, enhancing security by allowing homeowners to visually verify their visitors. This feature can be particularly beneficial for those who live in areas with high foot traffic or those who receive frequent deliveries.

The installation process is straightforward, as the device connects to existing wiring and does not require complicated setups or additional hardware. Moreover, it is designed to withstand various weather conditions, making it a durable choice for outdoor use.

In conclusion, the AT&T Door Phone Controller is an innovative solution for enhancing home security and communication. Its integration with existing telephone systems, high-quality audio technology, optional video capabilities, and ease of installation make it an excellent choice for homeowners looking to modernize their entryway while ensuring safety and convenience.
Top Page Image Contents