Audiovox DT 941 CI manual For dial tone. Then dial the number you want

Page 23

I

-@-

-i

Making Calls

You can make calls directly from the handset whether you are at the base or away from it.

Press the ~

key and wait

for dial tone. Then dial the number you want.

Or

2.Enter the number, then press the

~key. This will dial the number that is displayed on the handset after 2 seconds. See

ADVANCED DIALING.

If you make a mistake when dialing,

pres.12m to hang up, then press

the ~ key to get the dial tone again.

Disconnecting

To end a call, either place the handset back in the base, or press (Qffl on the handset.

Answering	Calls
When the	Handset rin~ss	any

key other than (Qff), lMUTEJ or the VOLUME keys to answer your call.

Volume Controls

The volume controls for the handset are located on the side of the unit. Press the A (up) "or '\1 (down) keys to increase or decrease the volume.

Holding either key down will

continuously change the volume setting. The earpiece volume level indicator on the dispaly will change accordingly. There are four volume levels.

21

FLASH"::' ::

You can use your AUDIOVOX

DT 941 CI cordless phone with services such as Call Waiting. Simply press

theiliill	key to FLASH the line.
	, .
REDIAL,	r

To REDIAL the last number you

dialed, .E!!!!-!!le~key.then press lREDIAl,1. The phone will automatically dial the number. The number will be shown on the display.

Clearing The Display' , i

The display can be cleared-by pressing and holding the ( CLR/D§Q key down until the display clears.

MUTE		c	:.-1..
.Press	~	duringaccinversation
to disable the handset microphone.
.Press	~	again	to return to
normal operation.
Rin g er	MUTE'		~';'f
			, .

.Press @QI§) while phone is ringing to disable the ringer for the duration of the call.

HOLD			.0		'~!
.Press		~	to	place	an	active-
call		on hold.
.The		Handset	will display		CALL ON
HOLD.
.Press~again				to return		to the
call.
PAGE		Handset	Locator		J
.~e		from	the Base Unit			press
l~J		.
.The		Handset	will	display		BASE
PAGING HANDSET.
.To	cancel the		pager either			press

~~on the Base Unit, or

press ~ on the Handset.

+

II

DT94102.p65

21

6/24/98, 12:20 PM

rF

Image 23

Contents COl\tl1\1UNICATIONS caRp ~,,1.~...?. ,, , -.,.,.., .~fl.,,!!t OT94102.p65 24/98 PM Special Features -ANSWERING Device Special Features PhoneTFI,EPHONE Line Cord Packs, call AudiovoxBase Unit Urations Combination of devices ~anu RJit~~rtC ~~~~~ Risks Audiovox Communications ~41Ftt Low battery message is Displayed111.1.1 Disposal, consult your local solid Battery into household garbage. ForImportant 00 not dispose of this Information on recycling or proper~a~ ~rl~t1gc- 0,!,,~~,.~i~t~t Telephonefill in the 11\ Ln.~Located on the back of the Base Unit. Figure ~~~=1t-~ Phone on is displayed when the phone is in use~-~ Repeat KEY Charging Contacts Base Unit Message Window LED ~~I~i.iOFF Program Location Memory Dialing speed Dialing ~f.t~l~~~~~~t?~r~~tifRitJ ~ilili.~iFor dial tone. Then dial the number you want 24/98 PM Your Dr 941 CI is capable of detecting Jm,irii~. ,.-, ...~l...!~~DVANeED Press ~ Or ~ To exitDisplay is cleared, then dial Normally Quick Memory Dialing On the display Dial mode and leave the numcerIi~e~~~n~~~~~ ~~6~tti~~~.~~~~ 111H T I 11t.~ .. l ~I~ L E T EI Press @1f to exit Alert signal, the LCD will display Name and number Caller ID serviceNumber when available will be With a Call Waiting signal. If you arePrivate CIDIrll Your DT 941 CI can answer incoming calls in 2 different ways SET Announce Onlyh It you would like to return to Tactory-set outgoing message ~~,~~~~,~f~iSet PLAY/STOP Base Ringer is on or OFFRemote Operation of the DT 941CI Repeat Answering Device -SET Security Code OT94102p65 OT94102.p6S FtJ None Thekeys YOU GET NOISE, sTATlc.16~ aPhone Doesnt Work AT ALL Handset does NOT, RingCommon Cure for Electronic Equipment OT94102p6S 6174/98 PM Receive Frequency WeightPower Reouirements FrequencyAudiovox Communications Corp Issueo