Audiovox DT 941 CI manual SET Announce Onlyh

Page 34

I

-@I-

Set Announce		Only
.Press	the~	key 5 times		until
you	hear:	"SET	ANNOUNCE
ONLYH
Now	press	~	.The	voice
prompt will say either OFF or ON.
Repeated		presses	of SELEC1;;:will
alternate between ON and OFF:
The Base Unit will display either
ON or OF (off) to reflect your
choice.

Choose OFF if you want your DT 941 CI to record your callers'

messages (Nbrmal Answering Mode).

Choose ON if you only want your callers to hear your greeting with- out allowing them to leave you a message (Announce-Only Mode).

Once you've selected OFF (or ON), press (TIME/SET) to confirm your selection. The voice prompt will say: "ANNOUNCE ONLY IS OFF (or ON)".

Set Outg~essage		1
.Press	~	until you hear "Set
Outgoing Message".
.Press	~.	The voice prompt
will say "Now Recording", followed
by	a tone.

.Begin speaking after the tone, towards the front edge of the Base Unit. The Base Unit display be- comes a timer as you record your outgoing message.

.Your outgoing message must be

longer than 2 seconds.

	MENU
--	..
<OC>	..
	MEMO
-~
o	-~I
)
	PLAY/STOP

.When done, press (PLAY/STOP1.

Your outgoing message will auto-

matica"y be played back.

You can now program the other 6 functions.

32

DT94102.p65

32

6124/98. 12:20 PM

-@-

Image 34

Contents COl\tl1\1UNICATIONS caRp ~,,1.~...?. ,, , -.,.,.., .~fl.,,!!t OT94102.p65 24/98 PM Special Features Phone Special Features -ANSWERING DeviceBase Unit Packs, call AudiovoxTFI,EPHONE Line Cord Urations Combination of devices ~~rtC ~~~~~ RJit~anu Risks ~41 Audiovox Communications111.1.1 Low battery message is DisplayedFtt Information on recycling or proper Battery into household garbage. ForImportant 00 not dispose of this Disposal, consult your local solid~a~ ~rl~t1gc- 0,!,,~~,.~i~t~t Ln.~ Telephonefill in the 11\~~~ Located on the back of the Base Unit. FigurePhone on is displayed when the phone is in use =1t-~~-~ Repeat KEY Charging Contacts OFF ~~I~i.iBase Unit Message Window LED Program Location ~ilili.~i ~f.t~l~~~~~~t?~r~~tifRitJ Memory Dialing speed DialingFor dial tone. Then dial the number you want 24/98 PM Press ~ Or ~ To exit Jm,irii~. ,.-, ...~l...!~~DVANeED Your Dr 941 CI is capable of detectingDisplay is cleared, then dial Normally Quick Memory Dialing Ii~e~~~n~~~~~ ~~6~tti~~~.~~~~ Dial mode and leave the numcerOn the display 111H T I 11t.~ .. l ~I~ L E T EI Press @1f to exit With a Call Waiting signal. If you are Name and number Caller ID serviceNumber when available will be Alert signal, the LCD will displayCID PrivateIrll Your DT 941 CI can answer incoming calls in 2 different ways SET Announce Onlyh ~~,~~~~,~f~i It you would like to return to Tactory-set outgoing messageSet Base Ringer is on or OFF PLAY/STOPRemote Operation of the DT 941CI Repeat Answering Device -SET Security Code OT94102p65 OT94102.p6S FtJ Handset does NOT, Ring YOU GET NOISE, sTATlc.16~ aPhone Doesnt Work AT ALL None ThekeysCommon Cure for Electronic Equipment OT94102p6S 6174/98 PM Frequency WeightPower Reouirements Receive FrequencyIssueo Audiovox Communications Corp