Audiovox DT 941 CI manual OT94102p65

Page 41

~

-w-

Approximately 10 seconds after new messages are played (or after the voice prompt says you have "NO new messages. ). you will hear the following menu:

.Press #2 to play all the

messages"

"Press #5 to stop"!,

"Press#4torepeat the message"

"Press #6 to skip the message" " Press #9 to erase the message "

"Press #1 for other functionsH

Upon pressing #1, you will hear the advanced menu:

"Press #7 to 'review outgoing

message"

"Press *7 to record outgoing

message"

"Press *8 to record memo"

" Press #4 twice to repeat

previous message"

"Press #0 to turn the system ON or OFF"

"Press #1 for other functions"

P ressing #1 at this point will return you to the first menu.

NOTE: Press .0 to exit remote operation mode. In addition, the DT 941 CI will exit remote opera- tion mode if there is approximately 15 seconds of inactivity.

Review Of Remote Commands

..'Press #2 to play all the messages ., The system will

announce how many new and old messages are in memory. If there are any new messages, the DT 941 CI will play the new messages only. Once all new messages are played. you can press #2 again to REPLAY all (old) messages.

39

"Press #5 to stop" Press #5

during review of messages to stop

playback.

"Press # 4 to repeat the

message II During message

review, press #4 to return to the beginning of the message being

played. Press #4 twice to return to the previous message.

.HPress #6 to skip the message"

During message review, press #6 to skip to the next message.

"Press #9 to erase the- message "

During message review, press #9 to erase the message being played.

"Press #7 to review outgoing

message"

To listen

to your

outgoing message, press #7.

"Press .7 to record outgoing

message "6To record a new

outgoing message ( replacing the

previous outgoing message ). press

.7. When your outgoing message is completed, hang up.

"Press .8 to record memo'. To -

record a memo, press .8. When

done, hang up.

HPress #0 to turn system on or offH As you press #0, the voice

prompt will toggle between

"Answering Machine ON" and "Answering Machine OFF".

+

il

OT94102p65

39

6/24/98. 12:20 PM

-~

rF

Image 41
Contents COl\tl1\1UNICATIONS caRp ~,,1.~...?. ,, , -.,.,.., .~fl.,,!!t OT94102.p65 24/98 PM Special Features -ANSWERING Device Special Features PhoneTFI,EPHONE Line Cord Packs, call AudiovoxBase Unit Urations Combination of devices ~anu RJit~~rtC ~~~~~ Risks Audiovox Communications ~41Ftt Low battery message is Displayed111.1.1 Important 00 not dispose of this Battery into household garbage. ForInformation on recycling or proper Disposal, consult your local solid~a~ ~rl~t1gc- 0,!,,~~,.~i~t~t Telephonefill in the 11\ Ln.~Located on the back of the Base Unit. Figure ~~~=1t-~ Phone on is displayed when the phone is in use~-~ Repeat KEY Charging Contacts Base Unit Message Window LED ~~I~i.iOFF Program Location RitJ ~f.t~l~~~~~~t?~r~~tif~ilili.~i Memory Dialing speed DialingFor dial tone. Then dial the number you want 24/98 PM ~. ,.-, ...~l...!~~DVANeED Jm,iriiPress ~ Or ~ To exit Your Dr 941 CI is capable of detectingDisplay is cleared, then dial Normally Quick Memory Dialing On the display Dial mode and leave the numcerIi~e~~~n~~~~~ ~~6~tti~~~.~~~~ 111H T I 11t.~ .. l ~I~ L E T EI Press @1f to exit Number when available will be Name and number Caller ID serviceWith a Call Waiting signal. If you are Alert signal, the LCD will displayPrivate CIDIrll Your DT 941 CI can answer incoming calls in 2 different ways SET Announce Onlyh It you would like to return to Tactory-set outgoing message ~~,~~~~,~f~iSet PLAY/STOP Base Ringer is on or OFFRemote Operation of the DT 941CI Repeat Answering Device -SET Security Code OT94102p65 OT94102.p6S FtJ Phone Doesnt Work AT ALL YOU GET NOISE, sTATlc.16~ aHandset does NOT, Ring None ThekeysCommon Cure for Electronic Equipment OT94102p6S 6174/98 PM Power Reouirements WeightFrequency Receive FrequencyAudiovox Communications Corp Issueo