AT&T PARTNER Plus Communications System Release 3 instruction

Installation Procedures

Before installing the system, be sure you read the safety instructions on page ii.

WARNING:

There are no customer-serviceable components inside the system modules or backplane. There are hazardous voltages within that can cause severe or fatal personal injury. DO NOT OPEN THE MODULES.

Installing the Control Unit and Modules

Install the control unit’s backplane within five feet (1.5 meters) of a properly grounded AC electrical outlet (not controlled by a switch) and the network interface jacks. In addition, when you mount the backplane on the wall, leave at least six inches (2.34 cm) of clearance at the top and sides, and two feet (0.6 meters) at the front and bottom to ensure proper ventilation.

1	A) Hold the backplane against the wall.
	B) Using the four screw keyholes in the backplane
	as a template, mark screw locations on the
	wall.
	C) Start four #12 screws, leaving the screw heads
	approximately 1/4” away from the wall.
	D) Slip the backplane onto the screws and tighten
2	them.
2	A) Slide the processor module into the center slot of
	the control unit—pressing the locking tab on
	the bottom of the slot as you push in the
	module will make insertion easier.
	B) Push slowly but firmly until the module locks into
	place with two snaps, and is attached to the
	rear of the backplane and held in place by the
	locking tab. Do not force the module. If it
	does not insert easily, remove the module,
3	clear any obstruction, and reinsert.
3	A) Slide the first 206 module into the leftmost slot of
	the backplane. (The system will not work if a
	206 module is not installed in this slot.)

B) Going from left to right, install 206 modules first, then any 400 (or 200) modules. The 400 modules should always be to the right of all 206 modules, so the extensions will be numbered consecutively. Hold down the locking tab and align the dovetail guides on the sides of the module with the guides on any previously inserted modules.

Backplane

Locking

Tab

Dovetail

Guides

Installation Procedures 7

PARTNER Plus Communications System Release 3 specifications

The AT&T PARTNER Plus Communications System Release 3 represents a significant advancement in business telecommunications, designed to cater to the needs of small to medium-sized enterprises. This versatile phone system offers a range of features, technologies, and characteristics that enhance productivity and streamline communication.

One of the hallmark features of the PARTNER Plus system is its modular design, allowing businesses to customize their communication setup according to their specific requirements. This scalability means that as a business grows or changes, the system can easily adapt without necessitating a complete overhaul. With support for up to 48 extensions, businesses can expand their communication capabilities seamlessly.

The system boasts a user-friendly interface that simplifies operation and management. The intuitive design enables users to navigate through features like call forwarding, voicemail, and conferencing with ease. Furthermore, the built-in Caller ID feature enhances call management, ensuring that users can identify incoming calls efficiently, contributing to better customer service.

The PARTNER Plus system also incorporates advanced voicemail capabilities, including the ability to assign voicemail to individual extensions. This feature allows for personalized messages, making it easier for customers to connect with the right department or individual. Voicemail-to-email integration is another powerful characteristic, enabling users to receive voice messages directly in their email inbox, enhancing accessibility.

In terms of technology, the PARTNER Plus system supports both analog and digital lines, offering flexibility in connectivity options. This adaptability allows businesses to choose the most economical solution based on their existing infrastructure. Additionally, the system supports telemarketing and call screening features, helping businesses manage sales and customer communications effectively.

Another notable characteristic of the PARTNER Plus system is its compatibility with various add-on equipment and accessories. This includes cordless handsets, speakerphones, and wireless headsets, which enhance mobility and communication ease within the workplace.

In conclusion, the AT&T PARTNER Plus Communications System Release 3 stands out as a robust and flexible solution for businesses seeking reliable, efficient, and sophisticated communication tools. With its combination of modular design, user-friendly features, and advanced technology, it effectively addresses the evolving demands of contemporary businesses while promoting improved connectivity and productivity. Whether for a small startup or an established enterprise, the PARTNER Plus system is an invaluable asset in navigating the complexities of modern communication.