–p time is simultaneously the duration of interdigit gap at pulse dialling.
5.5Presetting and Deleting
|
|
|
|
|
|
|
|
|
|
Parameter | Value | Description |
| Default | Exam.1 | Exam.2 | |||
|
|
|
|
|
|
|
|
|
|
8# | # | Default setting |
| executes |
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
8# | 1 | Setting per exam. 1 |
|
|
| executes |
|
| |
8# | 2 | Setting per exam. 2 |
|
|
|
|
| executes | |
|
|
|
|
|
|
|
|
| |
|
|
|
|
| |||||
This setting does not influence 1 and 2 (numbers stored in memory) |
|
| |||||||
|
|
|
|
|
| ||||
Parameter | Value | Description |
| Default | Exam.1 | Exam.2 | |||
81 |
| Deletes all numbers in |
|
|
|
|
| ||
| group 1 (Day mode) |
|
|
|
|
| |||
|
|
|
|
|
|
| |||
82 |
| Deletes all numbers in |
|
|
|
|
| ||
| group 2 (Night mode) |
|
|
|
|
| |||
|
|
|
|
|
|
| |||
83 |
| Default setting only | only 3.. |
|
|
| |||
| for parameters 3x |
|
|
|
| ||||
|
|
|
|
|
|
|
| ||
84 |
| Default setting only | only 4.. |
|
|
| |||
| for parameters 4x |
|
|
|
| ||||
|
|
|
|
|
|
|
| ||
85 |
| Default setting only | only 5.. |
|
|
| |||
| for parameters 5x |
|
|
|
| ||||
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
The parameters 81 and 82 will delete all numbers stored in memories for buttons.
The parameters 83 – 85 will execute a selective basic setting only for parameters starting with 3.. – 5.. ATTENTION !!! the deletion is
5.6 Exit programming
|
|
|
|
|
|
Parameter | Value | Description | Default | Exam.1 | Exam.2 |
9 |
| E N D |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
After dialling 9 the unit will hang up. If you hang up the phone during programming mode without press 9, the doorphone will stay in programming mode during 20 seconds.
5.7 System setting
|
|
|
|
|
|
Parameter | Value | Description | Default | Exam.1 | Exam.2 |
|
|
|
|
|
|
6# | s | Number of fitted buttons of |
|
|
|
basic module |
|
|
| ||
|
|
|
|
| |
|
|
|
|
|
|
The basic module is fitted with 4 buttons as standard, i.e. s = 1 is set up for basic module with one button and s = 2 for module with 2 buttons. This setting is a factory one, no service can change it and so it is recommended not to change this parameter.
Note: Connecting to the line the value of this parameter is checked and if not satisfactory for unknown reasons, so it is set up to s = 4 (fitted with 4 buttons).
ATTENTION !!! This parameter can cause the unit to function incorrectly.
|
|
|
|
|
|
Parametr | Value | Description | Default | Exam.1 | Exam.2 |
6 | z | Acoustic signalling | 3 and 9 | 3 and 9 | 3 and 9 |
|
|
|
|
|
|
|
|
|
|
|
|
In default the unit produces acoustic signals. It can occasionally cause a problem of incorrect detection of tones by PBX. By changing parameter „z“ you can switch off this acoustic signalization. The values are:
z=0 – all signalling is switched off
z=1 – pick up and hang up tones are active only z=2 – other tones active only (except pick up and hang up)
14