Anaheim DPJ72LC4, DPJ72LC3, DPJ72LC2 manual Table of Contents

Page 2

Table of Contents
GETTING STARTED	1
THANK YOU	1
PRODUCT SUPPORT	1
SYSTEM REQUIREMENTS	1
INSTALLING LC	2
USING THE MOUSE	2
CHOOSING COMMANDS	3
Choosing a Command by Using the Mouse	3
Choosing a Command by Using the Keyboard	3
Using Shortcut Keys	3
Using the TAB and ARROW Keys	3
USING STANDARD WINDOWS CONTROLS	3
Radio Buttons	3
Pull-Down Menus	4
Text Boxes	4
Command Buttons	4
SYSTEM SAFETY	5
ABOUT THIS MANUAL	6
PROGRAM OVERVIEW	6
MAIN SCREEN FEATURES	7
L	7
PULL DOWN MENU BAR	7
File Menu	7
Setup Menu	8
Controller Menu	9
View Menu	12
Help Menu	12
TOOL POSITION BOX	12
Program	13
Machine	13
Relative	13
Distance To Go	13
Other Features	13
TOOL PATH VIEW PORT	15
CONTROL BOX	16
G-Code Mode	17
Jog Mode	18
Point Mode	19
Home Mode	20
MESSAGE BOX	21
PROGRAM LISTING BOX	21
INITIAL SETUP	23
WINDOWS SETUP	23
SOFTWARE SETUP	24
The Setup File	24
System Settings	24
Machine Tool Settings	26
Feedrate and Ramping Settings	28
Setting Machine Zero	31
Setting Backlash	33
Tooling Settings	34
Input Line Settings	35
Output Line Settings	36
Motor Signal Settings	37

Image 2

Contents User’s Guide Table of Contents Error! Bookmark not defined Page System Requirements Thank YouProduct Support If you are using Windows 3.1 or Installing LCUsing the Mouse If you are using Windows 95, 98 or NTChoosing Commands Using Standard Windows ControlsText Boxes Command ButtonsPull-Down Menus System Safety About this Manual Program OverviewPull Down Menu Bar File MenuMain Screen Features Controller Menu Main Screen Features To change the state of an output line Help Menu Tool Position BoxView Menu Machine Other FeaturesProgram RelativeTo set new values within a coordinate system To zero each axisTool Path View Port To zero all axesControl Box Code Mode Jog Mode Point Mode Home Mode Message Box Program Listing BoxPage Windows Setup WindowsSystem Settings To set your system settings Software SetupSetup File Initial Setup Machine Tool Settings To set the Machine Tool Settings Initial Setup Feedrate and Ramping Settings To Set the Maximum Unramped FeedratesTo Set the Maximum Feedrates To Set the Ramping RateTo Set the Direction Change Delay To Set the Maximum Arc Feedrate Setting Machine ZeroTo Set the Jog Rates To Set Machine Zero Using Home Switches To Set Machine Zero Without Using Home SwitchesSetting Backlash To Set BacklashTooling Settings To Set Up the Tool LibraryInput Line Settings To Configure the Input LinesTo define an M-code to control output lines Output Line SettingsTo Configure the Output Lines Motor Signal Settings To Configure the Motor Signal LinesTo Configure G and M Code Handling Initial Setup Page To open an existing program Opening a G-Code ProgramImporting a DXF File To import a DXF fileTo choose a different file name or folder System Programming To edit a new program Using the Program EditorTo open the editor To save your program using the same file name To close the editorM Codes Supported Key Programming ConceptsMode Absolute vs. IncrementalM Code Reference G00 Rapid Tool PositioningG01 Linear Interpolated Cutting Move G02 Clockwise Circular Cutting MoveEnd G03 Counter Clockwise Circular Cutting Move End Center StartG20, G21 Inch Units and Metric Units G04 DwellG17, G18, G19 Arc Plane Selection G28 Return to Reference PointG29 Return from Reference Point System Programming System Programming System Programming System Programming G52 Local Coordinate System G90 Absolute Positioning Mode G91 Incremental Positioning ModeM30 End of Program M98, M99, M02 Subroutine CommandsM00 Program Pause Program Comments Feedrate CommandMXX Miscellaneous Device Control System Programming Windows 3.1 or Configuring LCStarting LC Software Windows 95, 98 or NTLoading a G-Code File Viewing the Tool Path Tutorial Animating the G-Code File Editing a G-Code File Connecting the Machine Online Using the Jog ControlsSetting Machine Zero Using the Point Move Setting Program Zero on the Machine Tool Testing the Program on the Machine Tool Turning off the Controller Cutting the PartExiting the Program O Connections Typical Output Configuration Driver BLD72 Series Driver Motor ON/OFF Input Internally ConnectedSetting the Kick Current Driver Page Glossary Glossary Glossary