Anaheim DPJ72LC2, DPJ72LC3, DPJ72LC4 manual Setting the Kick Current

Page 82

Section 7 Driver

SETTING THE KICK CURRENT

The Kick Current should be set to the Motor’s Rated Unipolar Current. For example, a 34D309 is rated for 4.5A, so the Kick Current Potentiometer would be set somewhere between the 4A and 5A indication.

GROUNDING

The unit should be properly grounded. Shielded cable should be used to preserve signal integrity.

MOTOR HOOKUP

The DPJ Series Driver Packs can drive 6-lead and 8-lead step motors rated from 1 to 7 amps/phase (unipolar rating). It features a unipolar bilevel (dual voltage) drive technique with short/open circuit protection (with a Fault LED). This Driver Pack contains a 600 Watt fan cooled power supply.

MOTOR CONNECTIONS

All motor connections must be separated from input connections and all other possible sources of interference.

IMPORTANT NOTE: When wiring from the driver(s) to the step motor(s) that extends beyond 25 feet, it is important to consult with the factory.

Image 82
Contents User’s Guide Table of Contents Error! Bookmark not defined Page Product Support Thank YouSystem Requirements If you are using Windows 3.1 or Installing LCUsing the Mouse If you are using Windows 95, 98 or NTChoosing Commands Using Standard Windows ControlsPull-Down Menus Command ButtonsText Boxes System Safety About this Manual Program OverviewPull Down Menu Bar File MenuMain Screen Features Controller Menu Main Screen Features To change the state of an output line View Menu Tool Position BoxHelp Menu Machine Other FeaturesProgram RelativeTo set new values within a coordinate system To zero each axisTool Path View Port To zero all axesControl Box Code Mode Jog Mode Point Mode Home Mode Message Box Program Listing BoxPage Windows Setup WindowsSetup File Software SetupSystem Settings To set your system settings Initial Setup Machine Tool Settings To set the Machine Tool Settings Initial Setup Feedrate and Ramping Settings To Set the Maximum Unramped FeedratesTo Set the Maximum Feedrates To Set the Ramping RateTo Set the Direction Change Delay To Set the Jog Rates Setting Machine ZeroTo Set the Maximum Arc Feedrate To Set Machine Zero Using Home Switches To Set Machine Zero Without Using Home SwitchesSetting Backlash To Set BacklashTooling Settings To Set Up the Tool LibraryInput Line Settings To Configure the Input LinesTo Configure the Output Lines Output Line SettingsTo define an M-code to control output lines Motor Signal Settings To Configure the Motor Signal LinesTo Configure G and M Code Handling Initial Setup Page To open an existing program Opening a G-Code ProgramImporting a DXF File To import a DXF fileTo choose a different file name or folder System Programming To open the editor Using the Program EditorTo edit a new program To save your program using the same file name To close the editorM Codes Supported Key Programming ConceptsMode Absolute vs. IncrementalM Code Reference G00 Rapid Tool PositioningG01 Linear Interpolated Cutting Move G02 Clockwise Circular Cutting MoveEnd G03 Counter Clockwise Circular Cutting Move End Center StartG20, G21 Inch Units and Metric Units G04 DwellG17, G18, G19 Arc Plane Selection G28 Return to Reference PointG29 Return from Reference Point System Programming System Programming System Programming System Programming G52 Local Coordinate System G90 Absolute Positioning Mode G91 Incremental Positioning ModeM00 Program Pause M98, M99, M02 Subroutine CommandsM30 End of Program MXX Miscellaneous Device Control Feedrate CommandProgram Comments System Programming Windows 3.1 or Configuring LCStarting LC Software Windows 95, 98 or NTLoading a G-Code File Viewing the Tool Path Tutorial Animating the G-Code File Editing a G-Code File Connecting the Machine Online Using the Jog ControlsSetting Machine Zero Using the Point Move Setting Program Zero on the Machine Tool Testing the Program on the Machine Tool Exiting the Program Cutting the PartTurning off the Controller O Connections Typical Output Configuration Driver BLD72 Series Driver Motor ON/OFF Input Internally ConnectedSetting the Kick Current Driver Page Glossary Glossary Glossary