Anaheim DPJ72LC3, DPJ72LC2, DPJ72LC4 manual Home Mode

Page 24

20		Section 2 Main Screen Features

Coord - The tool will move to the XYZ position in program coordinates, machine coordinates, relative coordinates, or incrementally from the current position of the tool, depending on the option you select in this pull-down menu.

Rate - You can set the feedrate by selecting one of the following from the pull- down menu:

Rapid - The machine tool moves at the maximum feedrate allowed by your current maximum feedrate settings in the Feedrate/Ramping Setup dialog box.

Feedrate - The machine tool moves at the feedrate you enter in the text box.

Home Mode

Start - Finds the home switch on all three axes. Homing moves each axis (one at a time) at a moderate feedrate to ensure that no steps are lost. To save time, it is recommended that you first jog each axis near the home switch before homing.

Once Machine Zero (home) is set, the machine tool envelope is redefined.

If Machine Zero was already set before homing, Anaheim Automation’s LC software displays a dialog showing the discrepancy between the previous Machine Zero and the new Machine Zero just found. This provides a convenient way to check that no steps were lost while cutting a part, within the accuracy limits of the home switch. The home switches supplied as an accessory, have a repeatability of +/-0.001”.

Image 24

Contents User’s Guide Table of Contents Error! Bookmark not defined Page Thank You Product SupportSystem Requirements Installing LC Using the MouseIf you are using Windows 3.1 or If you are using Windows 95, 98 or NTChoosing Commands Using Standard Windows ControlsCommand Buttons Pull-Down MenusText Boxes System Safety About this Manual Program OverviewPull Down Menu Bar File MenuMain Screen Features Controller Menu Main Screen Features To change the state of an output line Tool Position Box View MenuHelp Menu Other Features ProgramMachine RelativeTo set new values within a coordinate system To zero each axisTool Path View Port To zero all axesControl Box Code Mode Jog Mode Point Mode Home Mode Message Box Program Listing BoxPage Windows Setup WindowsSoftware Setup Setup FileSystem Settings To set your system settings Initial Setup Machine Tool Settings To set the Machine Tool Settings Initial Setup Feedrate and Ramping Settings To Set the Maximum Unramped FeedratesTo Set the Maximum Feedrates To Set the Ramping RateTo Set the Direction Change Delay Setting Machine Zero To Set the Jog RatesTo Set the Maximum Arc Feedrate To Set Machine Zero Using Home Switches To Set Machine Zero Without Using Home SwitchesSetting Backlash To Set BacklashTooling Settings To Set Up the Tool LibraryInput Line Settings To Configure the Input LinesOutput Line Settings To Configure the Output LinesTo define an M-code to control output lines Motor Signal Settings To Configure the Motor Signal LinesTo Configure G and M Code Handling Initial Setup Page Opening a G-Code Program Importing a DXF FileTo open an existing program To import a DXF fileTo choose a different file name or folder System Programming Using the Program Editor To open the editorTo edit a new program To save your program using the same file name To close the editorM Codes Supported Key Programming ConceptsMode Absolute vs. IncrementalM Code Reference G00 Rapid Tool PositioningG01 Linear Interpolated Cutting Move G02 Clockwise Circular Cutting MoveEnd G03 Counter Clockwise Circular Cutting Move End Center StartG04 Dwell G17, G18, G19 Arc Plane SelectionG20, G21 Inch Units and Metric Units G28 Return to Reference PointG29 Return from Reference Point System Programming System Programming System Programming System Programming G52 Local Coordinate System G90 Absolute Positioning Mode G91 Incremental Positioning ModeM98, M99, M02 Subroutine Commands M00 Program PauseM30 End of Program Feedrate Command MXX Miscellaneous Device ControlProgram Comments System Programming Configuring LC Starting LC SoftwareWindows 3.1 or Windows 95, 98 or NTLoading a G-Code File Viewing the Tool Path Tutorial Animating the G-Code File Editing a G-Code File Connecting the Machine Online Using the Jog ControlsSetting Machine Zero Using the Point Move Setting Program Zero on the Machine Tool Testing the Program on the Machine Tool Cutting the Part Exiting the ProgramTurning off the Controller O Connections Typical Output Configuration Driver BLD72 Series Driver Motor ON/OFF Input Internally ConnectedSetting the Kick Current Driver Page Glossary Glossary Glossary