Anaheim DPJ72LC3, DPJ72LC2, DPJ72LC4 manual Error! Bookmark not defined

Page 3

G and M Code Settings	38
SYSTEM PROGRAMMING	41
OPENING A G-CODEPROGRAM	41
IMPORTING A DXF FILE	41
USING THE PROGRAM EDITOR	44
G AND M CODES SUPPORTED	46
KEY PROGRAMMING CONCEPTS	46
Mode	47
Absolute vs. Incremental	47
G AND M CODE REFERENCE	48
G00 Rapid Tool Positioning	48
G01 Linear Interpolated Cutting Move	49
G02 Clockwise Circular Cutting Move	49
G03 Counter Clockwise Circular Cutting Move	51
G04 Dwell	52
G17, G18, G19 Arc Plane Selection	52
G20, G21 Inch Units and Metric Units	52
G28 Return to Reference Point	52
G29 Return from Reference Point	53
G43, G44, G49, M06 Tool Change and Tool Length Compensation Commands	54
G52 Local Coordinate System	58
G90 Absolute Positioning Mode	59
G91 Incremental Positioning Mode	59
M00 Program Pause	60
M30 End of Program	60
M98, M99, M02 Subroutine Commands	60
MXX – Miscellaneous Device Control	61
F Feedrate Command	61
Program Comments	61
TUTORIAL	63
STARTING LC SOFTWARE	63
Windows 3.1 or 3.11	63
Windows 95, 98 or NT	63
CONFIGURING LC	63
LOADING A G-CODEFILE	64
VIEWING THE TOOL PATH	65
ANIMATING THE G-CODEFILE	67
EDITING A G-CODEFILE	68
CONNECTING THE MACHINE ONLINE	69
USING THE JOG CONTROLS	69
SETTING MACHINE ZERO	70
USING THE POINT MOVE	71
SETTING PROGRAM ZERO ON THE MACHINE TOOL	72
TESTING THE PROGRAM ON THE MACHINE TOOL	73
CUTTING THE PART	74
EXITING THE PROGRAM	74
TURNING OFF THE CONTROLLER	74
I/O CONNECTIONS	75
WIRING	75
DRIVER (BLD72 SERIES DRIVER)	77
WIRING DIAGRAM	Error! Bookmark not defined.
GLOSSARY	81

Image 3

Contents User’s Guide Table of Contents Error! Bookmark not defined Page Thank You Product SupportSystem Requirements If you are using Windows 95, 98 or NT Installing LCUsing the Mouse If you are using Windows 3.1 orUsing Standard Windows Controls Choosing CommandsCommand Buttons Pull-Down MenusText Boxes System Safety Program Overview About this ManualFile Menu Pull Down Menu BarMain Screen Features Controller Menu Main Screen Features To change the state of an output line Tool Position Box View MenuHelp Menu Relative Other FeaturesProgram MachineTo zero each axis To set new values within a coordinate systemTo zero all axes Tool Path View PortControl Box Code Mode Jog Mode Point Mode Home Mode Program Listing Box Message BoxPage Windows Windows SetupSoftware Setup Setup FileSystem Settings To set your system settings Initial Setup Machine Tool Settings To set the Machine Tool Settings Initial Setup To Set the Maximum Unramped Feedrates Feedrate and Ramping SettingsTo Set the Ramping Rate To Set the Maximum FeedratesTo Set the Direction Change Delay Setting Machine Zero To Set the Jog RatesTo Set the Maximum Arc Feedrate To Set Machine Zero Without Using Home Switches To Set Machine Zero Using Home SwitchesTo Set Backlash Setting BacklashTo Set Up the Tool Library Tooling SettingsTo Configure the Input Lines Input Line SettingsOutput Line Settings To Configure the Output LinesTo define an M-code to control output lines To Configure the Motor Signal Lines Motor Signal SettingsTo Configure G and M Code Handling Initial Setup Page To import a DXF file Opening a G-Code ProgramImporting a DXF File To open an existing programTo choose a different file name or folder System Programming Using the Program Editor To open the editorTo edit a new program To close the editor To save your program using the same file nameKey Programming Concepts M Codes SupportedAbsolute vs. Incremental ModeG00 Rapid Tool Positioning M Code ReferenceG02 Clockwise Circular Cutting Move G01 Linear Interpolated Cutting MoveEnd End Center Start G03 Counter Clockwise Circular Cutting MoveG28 Return to Reference Point G04 DwellG17, G18, G19 Arc Plane Selection G20, G21 Inch Units and Metric UnitsG29 Return from Reference Point System Programming System Programming System Programming System Programming G52 Local Coordinate System G91 Incremental Positioning Mode G90 Absolute Positioning ModeM98, M99, M02 Subroutine Commands M00 Program PauseM30 End of Program Feedrate Command MXX Miscellaneous Device ControlProgram Comments System Programming Windows 95, 98 or NT Configuring LCStarting LC Software Windows 3.1 orLoading a G-Code File Viewing the Tool Path Tutorial Animating the G-Code File Editing a G-Code File Using the Jog Controls Connecting the Machine OnlineSetting Machine Zero Using the Point Move Setting Program Zero on the Machine Tool Testing the Program on the Machine Tool Cutting the Part Exiting the ProgramTurning off the Controller O Connections Typical Output Configuration Motor ON/OFF Input Internally Connected Driver BLD72 Series DriverSetting the Kick Current Driver Page Glossary Glossary Glossary