Philips M888 manual Power requirements, To avoid damage or malfunction

Page 5

1Important safety instructions

Power requirements

This product requires an electrical supply of 100-240 volts AC. In case of power failure, the communication can be lost.

The voltage on the network is classified as TNV-3 (Telecommunication Network Voltages), as defined in the standard EN 60950.

Warning

•• The Electrical network is classified as hazardous.The only way to power down the charger is to unplug the power supply from the electrical outlet. Ensure that the electrical outlet is always easily accessible.

To avoid damage or malfunction

Caution

•• Use only the power supply listed in the user instructions.

•• Use only the batteries listed in the user instructions.

•• Risk of explosion if battery is replaced by an incorrect type.

•• Dispose of used batteries according to the instructions.

•• Do not dispose of batteries in fire.

•• Always use the cables provided with the product.

•• Do not allow the charging contacts or the battery to come into contact with metal objects.

•• Do not let small metal objects come into contact with the product.This can deteriorate audio quality and damage the product.

•• Metallic objects may be retained if placed near or on the handset receiver.

•• Do not use the product in places where there are explosive hazards.

•• Do not open the handset, base station or charger as you could be exposed to high voltages.

•• For pluggable equipment, the socket-outlet shall be installed near the equipment and shall be easily accessible.

•• Handsfree activation could suddenly increase the volume in the earpiece to a very high level: make sure the handset is not too close to your ear.

•• This equipment is not designed to make emergency calls when the power fails. An alternative has to be made available to allow emergency calls.

•• Do not allow the product to come into contact with liquids.

•• Do not use any cleaning agents containing alcohol, ammonia, benzene, or abrasives as these may harm the set.

•• Do not expose the phone to excessive heat caused by heating equipment or direct sunlight.

•• Do not drop your phone or allow objects to fall on your phone.

•• Active mobile phones in the vicinity may cause interference.

When using the phone as a baby monitor

Caution

•• Children should be supervised to ensure that they do not play with the appliance.

•• Make sure the baby unit and the cord are always out of reach of the baby (at least 1 metre/3 feet away).

•• Keep the parent unit at least 1.5 metres/5 feet away from the baby unit to prevent acoustic feedback.

•• Never place the baby unit inside the baby’s bed or playpen.

•• Never cover the parent unit and the baby unit with anything (e.g. a towel or blanket). Always make sure the cooling vents of the baby unit are free.

•• Take every precaution to make sure that your baby can sleep safely .

•• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

•• If you place the parent unit next to a transmitter or other DECT appliance (e.g. a DECT telephone or wireless router for the internet), the connection with the baby unit may be lost. Move the baby monitor further away from the other wireless appliances until the connection is restored.

•• This baby monitor is intended as an aid. It is not a substitute for responsible and proper adult supervision and should not be used as such.

About operating and storage temperatures

Operate in a place where temperature is always between 0°C to +40°C (up to 90% relative humidity).

EN 3

Image 5
Contents Register your product and get support at Extended user documentationPage Contents Set the answer mode Announcements Incoming messages Turn off the alarmBatteries Text and number input tablesWhen using the phone as a baby monitor Power requirementsAbout operating and storage temperatures To avoid damage or malfunctionPage Handset Base station Power adapter Line cord Guarantee What is in the boxYour phone Overview of the phoneSet the dial mode pulse mode or temporary tone mode Overview of the base station Find handsets Enter the registration modeConnect the base station Install the handsetGet started Set the country/language Change the remote access PIN/passcodeSet the date and time Set the date and time formatWhat is standby mode? Check the battery levelCheck the signal strength Charge the handsetWhen ECO+ is on, the signal strength is not displayed Icon Descriptions Main menu iconsDisplay icons Answer a call CallsMake a call Switch between two calls Adjust the earpiece/speaker volumeEnd a call Mute the microphonePress , then or Make a conference call with the external callersMake a call to another handset Switch between callsTransfer a call Make a conference callDuring the conference call During an external callPress to add a space Enter text and numbersPhonebook Set the speed dial keys Edit a recordSet the personalized melody Delete all records Delete a recordAdd a contact to the exception list Set exceptionCall list type Call logView the call records Save a call record to the phonebookDelete all call records Delete a call recordRedial list ECO mode Phone settingsECO+ mode Set the date and timeSet the display language Name the handsetSet the alarm Alarm clockTurn off the alarm Before the alarm ringsSet the backlight of the LCD screen Display settingsSet the brightness Set the handsets ringtone volume Sound settingsSilent mode Exclude the contacts from silent modeAccess the sound profile during a call Set the battery toneSet the key tone Set the docking toneSend an alert Baby monitorActivate/Deactivate the baby unit Send to other handsetsSend to a contact from the phonebook Set the baby cry levelTurn the answering machine on or off Set the answer modeSet the answering machine language AnnouncementsIncoming messages Restore the default announcementRecord an announcement Listen to the announcementListen to the incoming messages Set the ring delayDelete an incoming message Delete all old incoming messagesChange the PIN/passcode Remote accessCall barring ServicesAuto conference Network type Auto prefixSelect the recall duration Set auto prefixFirst ring Dial modeAuto clock Register additional handsetsManual registration/Pairing Restore default settingsUnregister handsets Auto registrationDtmf Technical dataDisposal of your old product and batteries Declaration of conformityCompliance with EMF Page Read, what do I do? Frequently asked questionsHandset does not ring Text and number input tables Appendix48 EN Page 0168
Related manuals
Manual 11 pages 63 Kb