Oricom S6000 manual Setting up the Service Centre, Setting the Service Centre Number

Page 21

Press . Use to select between ON or OFF.

Setting up the Service Centre

To assist in set up the service centre numbers have been pre- programmed. These should not need to be changed.

SMS Centre 1 “183201983391” SMS Centre 2 “01983391”

IMORTANT NOTE:

If you normally have your Calling Number display blocked you must remove 1832 in front of 01983391 in the SMS centre otherwise you can not send a text message. However you should be aware that this will allow presentation of your phone number to the called party.

When the base unit is trying to make a connection with the service centre, the active service centre number will be used. However, messages from any service centre can be received.

Press . Use to select SMS.

Press . Use to select SETTINGS.

Press . Use to select SMSC.

Press . Use to select between SMS CENTRE 1 and SMS CENTRE 2.

Press to confirm.

Setting the Service Centre Number

Numbers for two service centres can be entered and one of them will be selected as the active service centre for outgoing messages.

Press . Use to select SMS.

Press . Use to select SETTINGS.

Press . Use to select SMS CENTRE1 or SMS CENTRE2.

Press .

The display will read NUMBER? and the previously entered number will be displayed.

Enter/edit the service centre number. Maximum of 18 digits can be entered.

Press to confirm.

Note: If there is no Service Centre number for the selected Service

Centre, SC NOT READY will be displayed when is pressed

to enter SMS menu or is being pressed and held from standby.

Since the Service Centre must recognize your CLI, the prefix to override the CLIR, 1832, has already been added in the factory programmed SMS centre 1 number. This prefix does not apply to any other calls.

To remove this prefix from the SMS centre 1 number is not recommended as the Service Centre may not recognize your call.

Setting up the Sub-Address

Sub address identifies each SMS-enabled device on the same telephone line. The default sub address is 0 and it doesn't need to be changed unless there are more than one SMS-enabled phones connected to the same line. When a call from Service Centre comes in, only the phone with intended sub address will answer the call.

Press . Use to select SMS.

21 of 42

Image 21
Contents Oricom S6000 Series Basic Operations Additional Features Appendix Default Settings Getting Started Contents of PackYour cordless phone Additional handsetsBasic steps to install LCD Display on the HandsetIcon Name Description Battery Level Indication Menu OverviewCharging the Handset Quick Dial Phonebook Menu Service MenuRedial Menu Call Log MenuUsing Traditional Dialling Basic OperationsTo End a Call Using Pre-Dialling Using Phonebook DiallingUsing Quick Dialling Using Re-Dialling Using Direct DiallingRedial the Dialled Number by Using Pre-dialling Redial the Last Dialled NumberWhen the handset is not on the base unit When the handset is on the base unit, lift the handsetDelete a Redial Number Making 2nd External CallUsing a Optional Headset Using the Handsfree SpeakerLow Power Mode Using the Phone BookHandset Keypad Lock/Unlock Storing an EntryEditing an Entry Reviewing the PhonebooksPage VIP Ringing Melody Deleting a Phonebook Entry in Private/Shared PhonebookCall Log Call Waiting Caller IDReview the Call Log Saving the CID record into phonebookSMS Service Using SMSDeleting a CID Record Call Back from the Call LogSetting up the Service Centre Setting the Service Centre NumberSetting up the Sub-Address Composing a Message Connection with the Service CentreSending Message Saving MessageReceiving Message Exit from Compose MessageDeleting the Message Forwarding the MessageReply and Delete the Message Replying the MessageSaving the Sender’s Number Calling the Sender’s NumberRetrieving Message from Outbox Editing the Saved Message Creating New Messages from the Saved MessagesSetting the Alert Tone SMS Error CodesDeleting the Saved Message Deleting all Messages in the InboxOne Touch access to Telstra Home Messages Additional FeaturesText Entry for SMS Message Waiting IndicationAdding a Service Operator ServicesReviewing Services Dialling out the Service NumberEditing Service Number Delete a ServicePrefix Matching Following call barring options can be selected Call BarringRinging Volume for Base Handset Ringer Melody for External CallsHandset Ringer Melody for Internal Calls Alert Tones Base Ringer Melody for External CallsOut of Range Warning Auto AnsweringCall Timer Adjust Time Display FormatFlash Recall Timing Handset NameChange the PIN Code for Base Backlit LCD / Backlit LCD & KeypadReset Factory Default Using Additional HandsetsDelete All Records RegistrationMaking Internal Calls Base SelectionInquiry Call Receiving external call during Internal CallCall Transfer Conference CallDe-register a Handset Room MonitoringTroubleshooting Appendix Default Settings‘02’ Customer support Warranty Information