Oricom S6000 manual Appendix Default Settings, Troubleshooting

Page 40

Appendix: Default Settings

External ringer melody (handset and base): MELODY 1

Internal ringer melody (handset): MELODY 2

Handset Ring Volume:

Base Ring Volume:

Receiver Volume: Med

Flash Timing: FLASH 1

Dial Mode: Tone

Auto Answer: On

Key Beep Tone: On

Confirmation Tone: On

Charging Tone: On

Backlit (if applicable): On

Call Timer: On

Message Waiting Indicator: Off

Monitor: Off

Direct Dial function: Off

Direct Dial number: Empty

Prefix Dialling: Off

Prefixes and numbers: Empty

Call Barring: Off

Call bar and exempt numbers: Empty

Operator services: Default services

Base Selection: Auto

PIN Code: 0000 (for base menu)

SMS Service: ON

Service centre numbers: Pre-programmed #

Active service centre: Service centre 1

Sub-Address: 0

SMS Alert Tone: On

Handset Name: ORICOM

Language: English

Troubleshooting

The phone does not work at all

Make sure that adapter and phone cord are connected properly.

Check that the batteries are fully charged and installed properly.

Check that the handset is correctly registered to the same base unit.

Move the handset closer to the base unit.

The phone does not ring

Make sure the adapter and the phone cord are connected properly.

Move the handset closer to the base unit.

Check that the handset is correctly registered to the same base unit.

Make sure the handset (or base) ringer is turned on.

The phone does not dial out

Check that the phone cord is connected properly.

Check the handset is fully charged.

Check that the handset is correctly registered to the same base unit.

The dialled number may be barred. See Call Barring section

The keypad may be locked. See Handset Keypad Lock/Unlock section.

CID does not work properly

Check with your local phone company that the CID service is subscribed to.

Let the phone ring at least once before answering.

The CIDCW call cannot be answered

Check with your local phone company and select the correct recall duration.

Base charge light does not work

Make sure that adapter is connected properly.

Make sure the handset is making contact in the cradle.

The empty battery icon appears soon after the batteries are charged

Replace the batteries with new ones.

40 of 42

Image 40
Contents Oricom S6000 Series Basic Operations Additional Features Appendix Default Settings Contents of Pack Getting StartedYour cordless phone Additional handsetsLCD Display on the Handset Basic steps to installIcon Name Description Menu Overview Battery Level IndicationCharging the Handset Quick Dial Service Menu Phonebook MenuRedial Menu Call Log MenuBasic Operations Using Traditional DiallingTo End a Call Using Phonebook Dialling Using Pre-DiallingUsing Quick Dialling Using Direct Dialling Using Re-DiallingRedial the Dialled Number by Using Pre-dialling Redial the Last Dialled NumberWhen the handset is on the base unit, lift the handset When the handset is not on the base unitDelete a Redial Number Making 2nd External CallUsing the Handsfree Speaker Using a Optional HeadsetUsing the Phone Book Low Power ModeHandset Keypad Lock/Unlock Storing an EntryReviewing the Phonebooks Editing an EntryPage Deleting a Phonebook Entry in Private/Shared Phonebook VIP Ringing MelodyCall Waiting Caller ID Call LogReview the Call Log Saving the CID record into phonebookUsing SMS SMS ServiceDeleting a CID Record Call Back from the Call LogSetting the Service Centre Number Setting up the Service CentreSetting up the Sub-Address Connection with the Service Centre Composing a MessageSending Message Saving MessageExit from Compose Message Receiving MessageDeleting the Message Forwarding the MessageReplying the Message Reply and Delete the MessageCalling the Sender’s Number Saving the Sender’s NumberRetrieving Message from Outbox Creating New Messages from the Saved Messages Editing the Saved MessageSMS Error Codes Setting the Alert ToneDeleting the Saved Message Deleting all Messages in the InboxAdditional Features One Touch access to Telstra Home MessagesText Entry for SMS Message Waiting IndicationOperator Services Adding a ServiceReviewing Services Dialling out the Service NumberDelete a Service Editing Service NumberPrefix Matching Call Barring Following call barring options can be selectedHandset Ringer Melody for External Calls Ringing Volume for BaseHandset Ringer Melody for Internal Calls Base Ringer Melody for External Calls Alert TonesOut of Range Warning Auto AnsweringAdjust Time Display Format Call TimerFlash Recall Timing Handset NameBacklit LCD / Backlit LCD & Keypad Change the PIN Code for BaseUsing Additional Handsets Reset Factory DefaultDelete All Records RegistrationBase Selection Making Internal CallsReceiving external call during Internal Call Inquiry CallCall Transfer Conference CallRoom Monitoring De-register a HandsetAppendix Default Settings Troubleshooting‘02’ Warranty Information Customer support