12Volt DS-2200 manual Listening While Audio Is Recorded Recording Monitor

Page 21

Listening While Audio Is Recorded (Recording Monitor)

If you start recording after inserting the earphone into the jack on the recorder, you can hear the sound being recorded. The sound volume on the recording monitor can be adjusted by pressing the VOL (+) or VOL (–) button.

1 Make sure that the recorder has stopped.

2 Connect the earphone to the jack on the recorder. After recording is started, you can hear the sound being recorded through the earphone.

.......................................................................................................

Notes

•Recording cannot be monitored during recording with an external microphone.

•Recording level cannot be controlled using the volume button.

•When recording using the remote controller microphone, recording cannot be monitored even though the earphone is connected to the

EAR jack on the remote controller.

• When using the earphones, do NOT set the volume too high. Listening at very high volume may lead to hearing loss.

2

Listening While

Audio Is

Recorded (Recording

Monitor)

21

Image 21

Contents DS-2200 Table of Contents Using the Recorder as a Reader / Writer Safe and Proper Usage General PrecautionsBatteries AC AdapterCase Main Features Card Basics Compatible cardsMemory Sizes of Cards and Approximate Recording Times*1 Identification of Parts Microphone MR12 Remote ControllerInserting Batteries Battery cover openLightly press down on the arrow and slide Insert two AAA alkaline batteries, observingUsing the AC Adapter Set the hour Setting Time/Date TIME&DATESet the minute Set the yearChanging the Time/Date Inserting and Ejecting a Card Inserting a CardCard not inserted fully into the slot Hold the card straight and pull it out Ejecting a Card1Press the Folder button to choose a folder Recording2Press the REC button to start recording Press the Stop button to stopPause Recording Recording functionsPause Resume Recording Press the FF or REW button until Setup screen Vcva flashes on the display Press the Play buttonAdjust the start/stop actuation level Recording with External Microphone Remote controller microphone MR12Make sure that the recorder has stopped Listening While Audio Is Recorded Recording MonitorREC Mode will be displayed on Recording Modes REC ModePress and hold the Menu button For 1 second or longerSuited for dictation Microphone SensitivityPress and hold the Menu button for 1 second or longer Recording From Another Audio DeviceWhen set to Stereo INPUT, the recorder starts recording Playing Record/play indicator lamp glows GreenPress the Play button to start Playback Can choose between 0 toPlayback functions Operation How to CancelPlayback through earphone PlayingPress the FF or REW button to choose between on and OFF Continuous Playback ALL PlayBack Space flashes on Auto Backspace review Back Space2 SEC Skip Press the REW button while the file is being replayedPress the Menu button again to choose a noise cancel level Noise Cancel FunctionPress the Repeat button briefly at Repeat PlaybackPress the Repeat button briefly Again at the position you wantPress the Stop button. Repeat Playback is cancelled Erasing One File at a Time ErasingErase All Files from a Folder When ALL ERASE? is flashingPress the Erase button for Seconds or longerLocking Files Lock 8 2,4,6Index Marks Setting an Index MarkLocating an Index Mark Clearing an Index MarkAlarm sounds Alarm Playback Function AlarmPress the Play button to complete the setup screen Choose between on and OFF11 12 8,10 To enable alarm sound onlyContrast flashes on LCD Contrast Adjustment ContrastPress the FF or REW button to set Contrast levelBacklight Backlight Assigning Folder Names Folder Name Press the FF or REW button to choose charactersCurrent character being entered Recorder buttons that are used to input characters Button Push ActionUse the two following methods to quickly find characters Type of Characters Action Available charactersWhen you have finished setting Assigning File Comments CommentInput the character Moving Files Across Folders 1Choose the file you want to move and play it3Press the FF or REW button to choose a destination folder OFF System sounds are disabled On System sounds are enabledSystem Sounds Beep Beep flashes on the displayWhile in stop or playback mode LCD Display InformationPress the Display button While recording in Vcva mode While in record modeRecording level meter Remaining memory barsRunning state when Hold is set Remember to reset the Hold switch when using the recorderHold Press the FF or REW button again to choose Start Formatting the Card FormatPress the Play button again Formatting the Card FormatPress and hold the Menu button for 1 second or longer Menu ListPrecautions on using the recorder connected to a PC Using DSS Player SoftwareRAM Operating EnvironmentInstalling DSS Player Software Insert Olympus DSS Player CD into the CD-ROM driveDouble-click the following icon. OS Delete the Executable File Uninstalling DSS Player SoftwareDelete the Driver File Delete the Help FileTo start online Help Using Online HelpConnecting to your PC using the USB cable Connecting to Your PCRecorder Remote is displayed on recorder if USB cable is connectedConnecting to your PC using the cradle Place the recorder on the cradleRemove the recorder from the cradle Running DSS Player Select Olympus DSS Player Pro, then click Dictation ModuleManual start Start your Macintosh Running DSS PlayerPlay Control Bar Window NamesDictation Folder Window Device Manager WindowDownload Selected Files Download Voice Files from the RecorderSelect the folder Select the voice fileDownload complete Download the voice filePlay a Voice File Play the voice fileFile name Select the folder to upload Upload Voice Files to the RecorderUpload the voice file Upload completeClick the Transfer button Changing User ID Author IDEditing File Comments Changing a Folder NameChanging a folder name in the Voice Folder window Changing a folder name in the Device windowEditing a Template Select the voice file to be attached to the e-mail Send Voice Files with E-mailSend the e-mail Replaying Received FilesHow to Install and Activate Mail Function After installing Outlook 2000, start the program Install Mapi SubsystemDialog box for setting up Microsoft Outlook appears Select Corporate or WorkgroupType the profile name and click OK Installing Microsoft Outlook XPIf you select POP3, you will see the following dialog box After the setup is completed, openDSS Player Pro and click Tools Options, Mail tab, and selectActivate Send Mail Function Click the CreateCreate a Profile Start Windows Connecting the recorder to your PC Using the Recorder as a Reader/WriterOpen the Explorer or Finder window Copy the dataMessage Meaning Explanation Action Alarm Message ListMessage Meaning Explanation Symptom Probable cause Action TroubleshootingAccessories optional Specifications Technical Assistance and Support Technical Assistance and SupportOlympus America INC Canadian RFI