Panasonic KX-TG1861NZ Operating additional units, Registering a handset to a base unit

Page 27

Multi-unit Operation

Operating additional units

Additional handsets

Up to 6 handsets can be registered to a single base unit. Additional handsets will give you the freedom to, for example, have an intercom call with another handset while a third handset is on an outside call. See page 4 for information on ordering additional handsets.

Important:

LThe additional handset model recommended for use with this unit is noted on page 4. If other model handset is used, certain operations (handset settings, base unit settings, etc.) may not be available.

Additional base units

Handsets can be registered to up to 4 base units, allowing you to add additional base units and extend the area in which your handset(s) can be used. If a handset moves out of range of its base unit when Autois selected on base unit selection (page 28), it will look for another base unit to make or receive calls. A base unit and the handsets it communicates with is called a “radio cell”.

Note:

LCalls will be disconnected when the handset moves from one radio cell to another.

Registering a handset to a base unit

The included handset and base unit are preregistered. If for some reason the handset is not registered to the base unit (for example, w flashes even when the handset

is near the base unit), register the handset manually (page 27).

To register an additional handset to a base unit (easy registration)

After purchasing an additional handset, register it to the base unit. Ensure that the additional handset is switched on. If it is not on, press and hold {ih} for few seconds to turn the handset on.

1Lift the additional handset and press {ih} to put the handset in standby mode.

2Press and hold {x} on the base unit for about 3 seconds, until the registration tone sounds.

3Place the additional handset on the base unit. The registration tone continues to sound. With the handset still on the base unit, wait until a confirmation tone sounds and w stops flashing.

Note:

LIf an error tone sounds, or if w is still flashing, register the handset manually (manual registration; page 27).

LIf all registered handsets start ringing in step 2, press {x} to stop. Start again from step 1.

LCharge the batteries of your additional handset for about 7 hours before initial use.

LThis registration method cannot be used for handsets that have already been registered to a base unit. Register the handset manually (manual registration; page 27).

To register a handset to an additional base unit (manual registration)

You can register a handset to a base unit manually using the following method.

1"(middle soft key) iNi #

2Registrationi#

27

Image 27
Contents Model No. KX-TG1861NZ Introduction Making/Answering Calls Included accessories Accessory informationEnvironment Battery cautionImportant information GeneralImportant notice ControlsDisplays Soft key icons Action Key Icon ConnectionsBattery charge If you subscribe to an Adsl serviceLocation Screen saver mode Turning the power on/offTime Settings by Date and time Display languageErase i # Redial featureMaking calls Edit and Call i#Answering calls Other featuresHandset locator Finding and calling a handset phonebook entry Handset phonebookAdding entries to the handset phonebook CategoriesEditing entries in the handset phonebook Erasing entries from the handset phonebookOne touch dial Chain dial Handset settings Auto talk on/off Off*5 Other Options KeytonesKeytones on/off On Auto TalkNight mode Time settingsRinger setup AlarmRinger Setup i # Night Mode i # Select Category i # Setting the ring delay for night modeRinger Setup i # Night Mode i # Ring Delay i # Selecting categories to bypass night modeArea Code Call Restrict Other Options Base Unit PIN Base unit settingsRepeater Mode Call Options Recall/FlashCall Options i # Area Code i# Setting call restrictionCall options Selecting area codes to be deleted automaticallyCategory features for handset phonebook Using Caller ID serviceErasing caller information Caller listViewing the caller list and calling back Editing a caller’s phone number before calling backCaller ID Service Additional base units Operating additional unitsRegistering a handset to a base unit Additional handsetsCancelling a handset Cancelling a base unitSelecting a base unit Handset Setting the repeater modeOther Options i # Repeater Mode i # Increasing the range of the base unitCopying all entries Copying phonebook entriesCopying one entry Copy i#Character entry modes Characters available in each character entry modeWhen the unit displays the character entry screen Character entryExtended 1 character table N Extended 2 character table OCyrillic character table P Troubleshooting Error messagesProblem Cause & solution LWipe the battery ends S, T and the unit contacts Specifications PIN IndexPage Page Copyright Customer Support Centre Tel. No 272 Sales Department