Panasonic KX-TCD700AL Paging/Intercom, Transferring a Call without the Intercom, Conference

Page 26

700al australian 2 5 02 2/5/02 3:00 pm Page 26

Paging/Intercom

Transferring a call using the Intercom (continued)

3.(Handset 2) When the unit rings, Z O or N to answer.

4.(Handset 1) Transferring a call Z P

The transfer is completed. or

to return to the External Call Z N.

Transferring a Call without the Intercom

This feature enables you to transfer the call to another handset without waiting for the paged handset to answer.

Eg. Handset 1 is transferring a call to Handset 2.

1.(Handset 1)

During a call, Z N (Intercom icon turns on)

The call is put on hold.

2.(Handset 1) Z desired handset no. eg. B

You will hear an internal ring back tone until the other handset is answered.

3.(Handset 1) Z P

4.(Handset 2) When the unit rings, Z O to answer.

The transfer is completed.

If the paged handset is not answered within 30 seconds, a ring tone sounds at the paging handset. The paging handset can return to the call by pressing O.

Conference

During a call using the handset, you can make an intercom call to another handset and then combine the calls together to establish a conference call between handsets registered to the same base unit.

1.(Handset 1) During a call, Z N then enter the desired handset number eg. B.

The call is put on hold.

If there is no answer, Z N to return to the call.

2.(Handset 2) When the unit rings, Z O or N to answer.

3.(Handset 1) Z C to establish a conference call.

4.(Handset 1 or 2) Z P to hang up on conference call.

26

Image 26
Contents Operating Instructions Charge the batteries for approx hours before initial useImportant Information Dear purchaserAC Adaptor Telephone Line Cord/Plug Batteries AA size Contents Programmable Functions Useful Information On the Base Unit Getting Started ConnectionsBattery Strength Installing the Batteries in the HandsetBattery Charge Battery InformationRemember to charge the new batteries after replacement see Battery CautionBattery Replacement Getting StartedInstallations Environment Safety InstructionsSafety PlacementImportant Information for Australia only Safety InstructionsInstallation Wall Mounting Base Unit Cancel ButtonLocation of Controls HandsetIcons Symbols UsedHandset Display Shows that you should press the following keysBasic Start-up Operations To Redial the Last Number Dialled Making CallsTo Dial After Confirming the Entered Number To Redial After Confirming the Numbers in Redial MemoryTo Edit/Clear Numbers in the Redial List To Select the Receiver VolumeMaking Calls Direct CallAuto Talk Answering CallsAnswering Calls To Turn the Handset Ringer Off TemporarilyDialling a Stored Number Speed DiallingStoring Phone Numbers in Memory Speed Dial Menu Y orDisplay number to be saved Speed DiallingSaving Numbers in Speed Dial List save speed Checking the Number of New Calls Caller ID ServiceHow Caller Information is Displayed when a Call is Received Caller ID Service Caller ID Sub-MenuViewing the Caller List Using the Caller ListWhen Viewing Long Telephone Numbers What ‘⁄’ meansCalling Back from the Caller List Using the Caller ListFor Optional Multi-Unit Users Operating More than One HandsetPaging All Handsets from the Base Unit Transferring a Call using the IntercomPaging/Intercom Intercom between HandsetsTransferring a Call without the Intercom Handset 1 Z P Handset 2 When the unit rings, Z O to answerPaging/Intercom ConferenceUsing the Recall Feature Special FeaturesHow to Use the Pause Feature Using Caller ID TypeTo Cancel the Key Lock Special FeaturesSetting the Key Lock on Y for more than 2 secondsSummary of Programmable Functions On the HandsetSet Time of Alarm set time Setting Time Alarm FunctionTo Stop the Alarm Time alarm Set Battery Low Tone ON/OFF battery low on/off Setting Tone OptionsSet Range Warning Alarm ON/OFF range alarm on/off Set Key Confirmation Tone ON/OFF key tone on/offSelect the Talk Mode Display talk mode Setting Display OptionsSelect the Standby Mode Display standby mode Set Call Prohibition call bar see Setting Call OptionsSetting Direct Call ON/OFF set direct on/off see Set Direct Call ON/OFF set direct on/off Set Auto Talk ON/OFF auto talk Setting Other OptionsSelect Battery Type battery type Change Handset PIN hspin change Hold Ï on base unit for 10 secs RegistrationRegister a Handset to a Base Unit register hs Cancelling a Base Unit cancel base Select Base Unit select bs Automatic Base Unit Access autoSpecified Base Unit Access eg. base Reset Handset reset hs Function Initial SettingOr U Programmable Functions On the Base UnitBell Selection Select all handsets to ringSelect Flash Timing Select Flash ModeSelect Pause Timing Select Pause TimingProgrammable Functions On the Base Unit Cancelling a HandsetCancelling a Handset Set the Base Unit PINRestricted Numbers When you dial a restrictedCall Restriction Select Ringer Volume To Select the Base Unit Ringer VolumeSetting the Clock Setting the ClockReset Base Unit Function Initial SettingOption Covers Using the Belt Clip Problem Remedy Before Requesting HelpCall is being received. To answer, Z P then Telephone Double Adaptor Adding Another PhoneBefore Requesting Help Panasonic Technics 700al australian 2 5 02 2/5/02 300 pm 700al australian 2 5 02 2/5/02 300 pm N52