Panasonic KX-TCD700AL operating instructions Before Requesting Help, Problem Remedy

Page 50

700al australian 2 5 02 2/5/02 3:00 pm Page 50

Before Requesting Help

Problem

Remedy

The unit does not work.

•Turn the power ON (p.14).

•Check the settings.

•Charge the batteries fully (p.9).

•Clean the charge contacts and charge again (p.9).

•Unplug the AC adaptor and turn the power OFF to reset. Plug in the AC adaptor and turn the power ON. Then try again.

•The handset has been cancelled or has not been registered. Register the handset (p.38).

•Re-install the handset batteries and try again.

“Î” flashes and an alarm tone	• You are too far from the base unit. Move closer and
sounds when you Z O.	• try again.
	• Plug in the AC adaptor.

A busy tone sounds when you	• Another handset is in use.
Z O.

You cannot dial.	• The unit is in call prohibition mode. Cancel the mode
	(p.35).
	• The dialled number is restricted. Cancel the number
	(p.45).
	• Key lock mode is set. Cancel the mode (p.28).

“Î” flashes during a conversation	• The handset is out of range. Move closer to the
and the call is disconnected.	• base unit and make the call again.
	• Plug in the AC adaptor.

Static, sound cuts in/out, fades.	• Locate the handset and base unit away from other
Interference from other electrical	• electrical appliances.
units.	• Move closer to the base unit.

The handset does not ring.

•Turn the power ON (p.14).

•The ringer is set to OFF. Select the desired volume level (p.31).

The base unit does not ring.

•The ringer is set to OFF. Set to HIGH, MEDIUM or LOW (p.46).

You cannot program function items	• Programming is not possible while the unit is in the
such as the handset ringer volume.	• talk or intercom mode.
	• Do not pause for over 60 seconds while
	programming.

You cannot store a phone number	• You cannot store a phone number while the unit is
in memory.	• in the talk or intercom mode.
	• Do not pause for over 60 seconds while storing.

50

Image 50

Contents Operating Instructions Charge the batteries for approx hours before initial useImportant Information Dear purchaserAC Adaptor Telephone Line Cord/Plug Batteries AA size Contents Programmable Functions Useful Information On the Base Unit Getting Started ConnectionsBattery Strength Installing the Batteries in the HandsetBattery Charge Battery InformationRemember to charge the new batteries after replacement see Battery CautionBattery Replacement Getting StartedInstallations Environment Safety InstructionsSafety PlacementImportant Information for Australia only Safety InstructionsInstallation Wall Mounting Base Unit Cancel ButtonLocation of Controls HandsetIcons Symbols UsedHandset Display Shows that you should press the following keysBasic Start-up Operations To Redial the Last Number Dialled Making CallsTo Dial After Confirming the Entered Number To Redial After Confirming the Numbers in Redial MemoryTo Edit/Clear Numbers in the Redial List To Select the Receiver VolumeMaking Calls Direct CallAuto Talk Answering CallsAnswering Calls To Turn the Handset Ringer Off TemporarilyDialling a Stored Number Speed DiallingStoring Phone Numbers in Memory Speed Dial Menu Y orDisplay number to be saved Speed DiallingSaving Numbers in Speed Dial List save speed Checking the Number of New Calls Caller ID ServiceHow Caller Information is Displayed when a Call is Received Caller ID Service Caller ID Sub-MenuViewing the Caller List Using the Caller ListWhen Viewing Long Telephone Numbers What ‘⁄’ meansCalling Back from the Caller List Using the Caller ListFor Optional Multi-Unit Users Operating More than One HandsetPaging All Handsets from the Base Unit Transferring a Call using the IntercomPaging/Intercom Intercom between HandsetsTransferring a Call without the Intercom Handset 1 Z P Handset 2 When the unit rings, Z O to answerPaging/Intercom ConferenceUsing the Recall Feature Special FeaturesHow to Use the Pause Feature Using Caller ID TypeTo Cancel the Key Lock Special FeaturesSetting the Key Lock on Y for more than 2 secondsSummary of Programmable Functions On the HandsetSet Time of Alarm set time Setting Time Alarm FunctionTo Stop the Alarm Time alarm Set Battery Low Tone ON/OFF battery low on/off Setting Tone OptionsSet Range Warning Alarm ON/OFF range alarm on/off Set Key Confirmation Tone ON/OFF key tone on/offSelect the Talk Mode Display talk mode Setting Display OptionsSelect the Standby Mode Display standby mode Set Call Prohibition call bar see Setting Call OptionsSetting Direct Call ON/OFF set direct on/off see Set Direct Call ON/OFF set direct on/off Set Auto Talk ON/OFF auto talk Setting Other OptionsSelect Battery Type battery type Change Handset PIN hspin change Hold Ï on base unit for 10 secs RegistrationRegister a Handset to a Base Unit register hs Cancelling a Base Unit cancel base Select Base Unit select bs Automatic Base Unit Access autoSpecified Base Unit Access eg. base Reset Handset reset hs Function Initial SettingOr U Programmable Functions On the Base UnitBell Selection Select all handsets to ringSelect Flash Timing Select Flash ModeSelect Pause Timing Select Pause TimingProgrammable Functions On the Base Unit Cancelling a HandsetCancelling a Handset Set the Base Unit PINRestricted Numbers When you dial a restrictedCall Restriction Select Ringer Volume To Select the Base Unit Ringer VolumeSetting the Clock Setting the Clock Reset Base Unit Function Initial SettingOption Covers Using the Belt Clip Problem Remedy Before Requesting HelpCall is being received. To answer, Z P then Telephone Double Adaptor Adding Another PhoneBefore Requesting Help Panasonic Technics 700al australian 2 5 02 2/5/02 300 pm 700al australian 2 5 02 2/5/02 300 pm N52