Panasonic KX-TCD700AL operating instructions Call is being received. To answer, Z P then

Page 51

700al australian 2 5 02 2/5/02 3:00 pm Page 51

	➡


Problem	Remedy
While programming or searching,	• To answer the call, lift the handset or Z O.
the unit starts to ring and stops	• Start again from the beginning after hanging up.
the program/search.

The unit does not display the	• Other telephone equipment may be interfering with
caller’s phone numbers.	• your phone. Disconnect them and try again.
	• Other electrical appliances connected to the same
	outlet may be interfering with the Caller ID
	information. Telephone line noise may be affecting
	the Caller ID information.

Ï does not function.	• The handset is too far from the base unit.
	• The handset is engaged in an outside call.

You cannot redial.	• If the last number dialled was more than 24 digits
	long, the number will not be redialled correctly.

The paged handset does not	• The handset is not in the same radio area.
answer.	• The handset is engaged in an outside call.
	• The handset has been cancelled or has not been
	registered. Register the handset to the base unit
	(p.38).

While using the intercom, two tones	• A call is being received. To answer, Z P then
sound.	O.

The unit misdials when connected	• Check the pause function (p.27).
to a PBX.

You cannot register the handset	• The base unit has registered a maximum of 6
in the base unit.	• handsets or the handset has registered a maximum
	of 4 base units.
	• A wrong base unit password was entered. Enter the
	correct password.
	• There is interference from other electrical units,
	locate the handset and base unit away from them.
	• You must finish registration within 1 minute after the
	ringer tone sounds, or programming will be
	cancelled (p.38).
	cancelled (p.38).

The battery strength is not	• Check that the battery type selection is correct		CHAPTER 5
displayed correctly.	• (p.36).

51

Image 51

Contents Charge the batteries for approx hours before initial use Operating InstructionsDear purchaser Important InformationAC Adaptor Telephone Line Cord/Plug Batteries AA size Contents Programmable Functions Useful Information On the Base Unit Connections Getting StartedBattery Information Installing the Batteries in the HandsetBattery Charge Battery StrengthGetting Started Battery CautionBattery Replacement Remember to charge the new batteries after replacement seePlacement Safety InstructionsSafety Installations EnvironmentSafety Instructions InstallationImportant Information for Australia only Wall Mounting Handset Cancel ButtonLocation of Controls Base UnitShows that you should press the following keys Symbols UsedHandset Display IconsBasic Start-up Operations To Redial After Confirming the Numbers in Redial Memory Making CallsTo Dial After Confirming the Entered Number To Redial the Last Number DialledDirect Call To Select the Receiver VolumeMaking Calls To Edit/Clear Numbers in the Redial ListTo Turn the Handset Ringer Off Temporarily Answering CallsAnswering Calls Auto TalkSpeed Dialling Storing Phone Numbers in MemoryDialling a Stored Number Y or Speed Dial MenuSpeed Dialling Saving Numbers in Speed Dial List save speedDisplay number to be saved Caller ID Service How Caller Information is Displayed when a Call is ReceivedChecking the Number of New Calls Caller ID Sub-Menu Caller ID ServiceWhat ‘⁄’ means Using the Caller ListWhen Viewing Long Telephone Numbers Viewing the Caller ListOperating More than One Handset Using the Caller ListFor Optional Multi-Unit Users Calling Back from the Caller ListIntercom between Handsets Transferring a Call using the IntercomPaging/Intercom Paging All Handsets from the Base UnitConference Handset 1 Z P Handset 2 When the unit rings, Z O to answerPaging/Intercom Transferring a Call without the IntercomUsing Caller ID Type Special FeaturesHow to Use the Pause Feature Using the Recall FeatureY for more than 2 seconds Special FeaturesSetting the Key Lock on To Cancel the Key LockOn the Handset Summary of Programmable FunctionsSetting Time Alarm Function To Stop the AlarmSet Time of Alarm set time Time alarm Set Key Confirmation Tone ON/OFF key tone on/off Setting Tone OptionsSet Range Warning Alarm ON/OFF range alarm on/off Set Battery Low Tone ON/OFF battery low on/offSetting Display Options Select the Standby Mode Display standby modeSelect the Talk Mode Display talk mode Setting Call Options Setting Direct Call ON/OFF set direct on/off seeSet Call Prohibition call bar see Set Direct Call ON/OFF set direct on/off Setting Other Options Select Battery Type battery typeSet Auto Talk ON/OFF auto talk Change Handset PIN hspin change Registration Register a Handset to a Base Unit register hsHold Ï on base unit for 10 secs Cancelling a Base Unit cancel base Automatic Base Unit Access auto Specified Base Unit Access eg. baseSelect Base Unit select bs Function Initial Setting Reset Handset reset hsSelect all handsets to ring Programmable Functions On the Base UnitBell Selection Or USelect Pause Timing Select Flash ModeSelect Pause Timing Select Flash TimingSet the Base Unit PIN Cancelling a HandsetCancelling a Handset Programmable Functions On the Base UnitWhen you dial a restricted Call RestrictionRestricted Numbers Setting the Clock To Select the Base Unit Ringer VolumeSetting the Clock Select Ringer VolumeFunction Initial Setting Reset Base UnitOption Covers Using the Belt Clip Before Requesting Help Problem RemedyCall is being received. To answer, Z P then Adding Another Phone Before Requesting HelpTelephone Double Adaptor Panasonic Technics 700al australian 2 5 02 2/5/02 300 pm 700al australian 2 5 02 2/5/02 300 pm N52