Panasonic KX-TCD700AL Installing the Batteries in the Handset, Battery Charge, Battery Strength

Page 7

700al australian 2 5 02 2/5/02 3:00 pm Page 7

Installing the Batteries in the Handset

• If the rechargeable batteries are not inserted correctly, the handset will not work.

Battery Charge

 

 

 

 

 

Full

Low

 

 

At the time of shipment, the batteries

 

 

Flashing

 

are not charged. To charge, place the

 

 

 

 

 

 

 

 

 

 

 

 

handset on the base unit. Please charge the batteries for approximately 10 hours before initial use. During charging, the battery icon is as shown above.

Battery Strength

You can check the present battery strength on the display.

Battery strength

Fully charged

Medium

Low

No power

Battery icon

Ò

Ú

Û

Û (Flashing)

 

 

 

 

 

 

Recharge

When “Û” flashes or the unit beeps every 15 seconds, recharge the batteries.

Battery Information

After your batteries are fully charged:

Operation

Ni-MH battery life (Included)

Ni-Cd battery life (optional)

 

 

 

While in use (Talk)

Approx. 20 hours

Approx. 12 hours (based on 800mA per hour)

 

 

 

While not in use (Stand-By)

Approx. 160 hours

Approx. 100 hours

 

 

 

Battery life may vary depending on usage conditions, such as:

when viewing the Caller ID Caller List, and

ambient temperature.

Clean the handset charge contacts with a soft, dry cloth once a month. Clean more often if the unit is subject to grease, dust or high humidity. Otherwise the batteries may not charge properly.

To maximise battery life, it is advisable not to place the handset on the base unit until “Û” flashes.

The batteries cannot be overcharged.

CHAPTER 1

7

Image 7
Contents Charge the batteries for approx hours before initial use Operating InstructionsDear purchaser Important InformationAC Adaptor Telephone Line Cord/Plug Batteries AA size Contents Programmable Functions Useful Information On the Base Unit Connections Getting StartedBattery Information Installing the Batteries in the HandsetBattery Charge Battery StrengthGetting Started Battery CautionBattery Replacement Remember to charge the new batteries after replacement seePlacement Safety InstructionsSafety Installations EnvironmentInstallation Safety InstructionsImportant Information for Australia only Wall Mounting Handset Cancel ButtonLocation of Controls Base UnitShows that you should press the following keys Symbols UsedHandset Display IconsBasic Start-up Operations To Redial After Confirming the Numbers in Redial Memory Making CallsTo Dial After Confirming the Entered Number To Redial the Last Number DialledDirect Call To Select the Receiver VolumeMaking Calls To Edit/Clear Numbers in the Redial ListTo Turn the Handset Ringer Off Temporarily Answering CallsAnswering Calls Auto TalkStoring Phone Numbers in Memory Speed DiallingDialling a Stored Number Y or Speed Dial MenuSaving Numbers in Speed Dial List save speed Speed DiallingDisplay number to be saved How Caller Information is Displayed when a Call is Received Caller ID ServiceChecking the Number of New Calls Caller ID Sub-Menu Caller ID ServiceWhat ‘⁄’ means Using the Caller ListWhen Viewing Long Telephone Numbers Viewing the Caller ListOperating More than One Handset Using the Caller ListFor Optional Multi-Unit Users Calling Back from the Caller ListIntercom between Handsets Transferring a Call using the IntercomPaging/Intercom Paging All Handsets from the Base UnitConference Handset 1 Z P Handset 2 When the unit rings, Z O to answerPaging/Intercom Transferring a Call without the IntercomUsing Caller ID Type Special FeaturesHow to Use the Pause Feature Using the Recall FeatureY for more than 2 seconds Special FeaturesSetting the Key Lock on To Cancel the Key LockOn the Handset Summary of Programmable FunctionsTo Stop the Alarm Setting Time Alarm FunctionSet Time of Alarm set time Time alarm Set Key Confirmation Tone ON/OFF key tone on/off Setting Tone OptionsSet Range Warning Alarm ON/OFF range alarm on/off Set Battery Low Tone ON/OFF battery low on/offSelect the Standby Mode Display standby mode Setting Display OptionsSelect the Talk Mode Display talk mode Setting Direct Call ON/OFF set direct on/off see Setting Call OptionsSet Call Prohibition call bar see Set Direct Call ON/OFF set direct on/off Select Battery Type battery type Setting Other OptionsSet Auto Talk ON/OFF auto talk Change Handset PIN hspin change Register a Handset to a Base Unit register hs RegistrationHold Ï on base unit for 10 secs Cancelling a Base Unit cancel base Specified Base Unit Access eg. base Automatic Base Unit Access autoSelect Base Unit select bs Function Initial Setting Reset Handset reset hsSelect all handsets to ring Programmable Functions On the Base UnitBell Selection Or USelect Pause Timing Select Flash ModeSelect Pause Timing Select Flash TimingSet the Base Unit PIN Cancelling a HandsetCancelling a Handset Programmable Functions On the Base UnitCall Restriction When you dial a restrictedRestricted Numbers Setting the Clock To Select the Base Unit Ringer VolumeSetting the Clock Select Ringer VolumeFunction Initial Setting Reset Base UnitOption Covers Using the Belt Clip Before Requesting Help Problem RemedyCall is being received. To answer, Z P then Before Requesting Help Adding Another PhoneTelephone Double Adaptor Panasonic Technics 700al australian 2 5 02 2/5/02 300 pm 700al australian 2 5 02 2/5/02 300 pm N52