Panasonic KX-TCD700AL Getting Started, Battery Caution, Battery Replacement, Base Unit Location

Page 8

700al australian 2 5 02 2/5/02 3:00 pm Page 8

➡Getting Started

Battery Caution:

To reduce the risk of fire or injury to persons, read and follow these instructions.

1.Use only the batteries specified.

2.Do not use non-rechargeable batteries.

3.Do not mix old and new batteries.

4.Do not dispose of the batteries in a fire. They may explode. Check with local waste management codes for special disposal instructions.

5.Do not open or mutilate the batteries. Released electrolyte is corrosive and may cause burns or injury to the eyes or skin. The electrolyte may be toxic if swallowed.

6.Exercise care in handling the batteries in order not to short the batteries with conductive materials such as rings, bracelets, and keys. The batteries and/or conductor may overheat and cause burns.

7.Charge the batteries provided with or identified for use with this product only in accordance with the instructions and limitations specified in this manual.

Battery Replacement:

If “Û” flashes after a few telephone calls even when the handset batteries have been fully charged, it is time to replace the batteries with new ones.

Remember to charge the new batteries after replacement (see page 7).

•Discard defective batteries as soon as possible. Defective batteries may leak into the unit.

Base Unit Location:

For maximum distance and noise-free operation, the recommended base unit location is:

•Away from electrical appliances such as TV, radio, personal computer or another telephone.

•In a convenient high and central location.

8

Image 8

Contents Operating Instructions Charge the batteries for approx hours before initial useImportant Information Dear purchaserAC Adaptor Telephone Line Cord/Plug Batteries AA size Contents Programmable Functions Useful Information On the Base Unit Getting Started ConnectionsInstalling the Batteries in the Handset Battery ChargeBattery Strength Battery InformationBattery Caution Battery ReplacementRemember to charge the new batteries after replacement see Getting StartedSafety Instructions SafetyInstallations Environment PlacementImportant Information for Australia only Safety InstructionsInstallation Wall Mounting Cancel Button Location of ControlsBase Unit HandsetSymbols Used Handset DisplayIcons Shows that you should press the following keysBasic Start-up Operations Making Calls To Dial After Confirming the Entered NumberTo Redial the Last Number Dialled To Redial After Confirming the Numbers in Redial MemoryTo Select the Receiver Volume Making CallsTo Edit/Clear Numbers in the Redial List Direct CallAnswering Calls Answering CallsAuto Talk To Turn the Handset Ringer Off TemporarilyDialling a Stored Number Speed DiallingStoring Phone Numbers in Memory Speed Dial Menu Y orDisplay number to be saved Speed DiallingSaving Numbers in Speed Dial List save speed Checking the Number of New Calls Caller ID ServiceHow Caller Information is Displayed when a Call is Received Caller ID Service Caller ID Sub-MenuUsing the Caller List When Viewing Long Telephone NumbersViewing the Caller List What ‘⁄’ meansUsing the Caller List For Optional Multi-Unit UsersCalling Back from the Caller List Operating More than One HandsetTransferring a Call using the Intercom Paging/IntercomPaging All Handsets from the Base Unit Intercom between HandsetsHandset 1 Z P Handset 2 When the unit rings, Z O to answer Paging/IntercomTransferring a Call without the Intercom ConferenceSpecial Features How to Use the Pause FeatureUsing the Recall Feature Using Caller ID TypeSpecial Features Setting the Key Lock onTo Cancel the Key Lock Y for more than 2 secondsSummary of Programmable Functions On the HandsetSet Time of Alarm set time Setting Time Alarm FunctionTo Stop the Alarm Time alarm Setting Tone Options Set Range Warning Alarm ON/OFF range alarm on/offSet Battery Low Tone ON/OFF battery low on/off Set Key Confirmation Tone ON/OFF key tone on/offSelect the Talk Mode Display talk mode Setting Display OptionsSelect the Standby Mode Display standby mode Set Call Prohibition call bar see Setting Call OptionsSetting Direct Call ON/OFF set direct on/off see Set Direct Call ON/OFF set direct on/off Set Auto Talk ON/OFF auto talk Setting Other OptionsSelect Battery Type battery type Change Handset PIN hspin change Hold Ï on base unit for 10 secs RegistrationRegister a Handset to a Base Unit register hs Cancelling a Base Unit cancel base Select Base Unit select bs Automatic Base Unit Access autoSpecified Base Unit Access eg. base Reset Handset reset hs Function Initial SettingProgrammable Functions On the Base Unit Bell SelectionOr U Select all handsets to ringSelect Flash Mode Select Pause TimingSelect Flash Timing Select Pause TimingCancelling a Handset Cancelling a HandsetProgrammable Functions On the Base Unit Set the Base Unit PINRestricted Numbers When you dial a restrictedCall Restriction To Select the Base Unit Ringer Volume Setting the ClockSelect Ringer Volume Setting the ClockReset Base Unit Function Initial SettingOption Covers Using the Belt Clip Problem Remedy Before Requesting HelpCall is being received. To answer, Z P then Telephone Double Adaptor Adding Another PhoneBefore Requesting Help Panasonic Technics 700al australian 2 5 02 2/5/02 300 pm 700al australian 2 5 02 2/5/02 300 pm N52