Panasonic KX-TCD700AL operating instructions Getting Started, Connections

Page 6

700al australian 2 5 02 2/5/02 3:00 pm Page 6

Getting Started

Connections

Plug in the AC Adaptor and the telephone line cord to the rear of the unit. Then connect the cord as shown.

Hook

Fasten the AC adaptor cord to prevent it from being disconnected

LINE

To Telephone Socket

Telephone Line Cord

To Mains Outlet

(AC 220-240V, 50Hz)

AC Adaptor

USE ONLY WITH Panasonic AC ADAPTOR PQLV1AL.

•The AC Adaptor must remain connected at all times. (It is normal for the adaptor to feel warm during use.)

•To connect a standard telephone on the same line, see page 52.

•If your unit is connected to a telephone line or PBX which does not support Caller ID services, you cannot access those services.

Image 6

Contents Operating Instructions Charge the batteries for approx hours before initial useImportant Information Dear purchaserAC Adaptor Telephone Line Cord/Plug Batteries AA size Contents Programmable Functions Useful Information On the Base Unit Getting Started ConnectionsBattery Strength Installing the Batteries in the HandsetBattery Charge Battery InformationRemember to charge the new batteries after replacement see Battery CautionBattery Replacement Getting StartedInstallations Environment Safety InstructionsSafety PlacementSafety Instructions InstallationImportant Information for Australia only Wall Mounting Base Unit Cancel ButtonLocation of Controls HandsetIcons Symbols UsedHandset Display Shows that you should press the following keysBasic Start-up Operations To Redial the Last Number Dialled Making CallsTo Dial After Confirming the Entered Number To Redial After Confirming the Numbers in Redial MemoryTo Edit/Clear Numbers in the Redial List To Select the Receiver VolumeMaking Calls Direct CallAuto Talk Answering CallsAnswering Calls To Turn the Handset Ringer Off TemporarilySpeed Dialling Storing Phone Numbers in MemoryDialling a Stored Number Speed Dial Menu Y orSpeed Dialling Saving Numbers in Speed Dial List save speedDisplay number to be saved Caller ID Service How Caller Information is Displayed when a Call is ReceivedChecking the Number of New Calls Caller ID Service Caller ID Sub-MenuViewing the Caller List Using the Caller ListWhen Viewing Long Telephone Numbers What ‘⁄’ meansCalling Back from the Caller List Using the Caller ListFor Optional Multi-Unit Users Operating More than One HandsetPaging All Handsets from the Base Unit Transferring a Call using the IntercomPaging/Intercom Intercom between HandsetsTransferring a Call without the Intercom Handset 1 Z P Handset 2 When the unit rings, Z O to answerPaging/Intercom ConferenceUsing the Recall Feature Special FeaturesHow to Use the Pause Feature Using Caller ID TypeTo Cancel the Key Lock Special FeaturesSetting the Key Lock on Y for more than 2 secondsSummary of Programmable Functions On the HandsetSetting Time Alarm Function To Stop the AlarmSet Time of Alarm set time Time alarm Set Battery Low Tone ON/OFF battery low on/off Setting Tone OptionsSet Range Warning Alarm ON/OFF range alarm on/off Set Key Confirmation Tone ON/OFF key tone on/offSetting Display Options Select the Standby Mode Display standby modeSelect the Talk Mode Display talk mode Setting Call Options Setting Direct Call ON/OFF set direct on/off seeSet Call Prohibition call bar see Set Direct Call ON/OFF set direct on/off Setting Other Options Select Battery Type battery typeSet Auto Talk ON/OFF auto talk Change Handset PIN hspin change Registration Register a Handset to a Base Unit register hsHold Ï on base unit for 10 secs Cancelling a Base Unit cancel base Automatic Base Unit Access auto Specified Base Unit Access eg. baseSelect Base Unit select bs Reset Handset reset hs Function Initial SettingOr U Programmable Functions On the Base UnitBell Selection Select all handsets to ringSelect Flash Timing Select Flash ModeSelect Pause Timing Select Pause TimingProgrammable Functions On the Base Unit Cancelling a HandsetCancelling a Handset Set the Base Unit PINWhen you dial a restricted Call RestrictionRestricted Numbers Select Ringer Volume To Select the Base Unit Ringer VolumeSetting the Clock Setting the ClockReset Base Unit Function Initial SettingOption Covers Using the Belt Clip Problem Remedy Before Requesting HelpCall is being received. To answer, Z P then Adding Another Phone Before Requesting HelpTelephone Double Adaptor Panasonic Technics 700al australian 2 5 02 2/5/02 300 pm 700al australian 2 5 02 2/5/02 300 pm N52