Uniden DECT1915 manual Making and answering calls, To make a Call Key in the telephone number

Page 16

BASIC USE

Making and answering calls

To make a

1

call

2

Key in the telephone number

If you make a mistake, press the left Soft button [Clear] to clear digits from the display.

Press the PHONE button

(You can dial the number after you press the PHONE button to get Dial tone if you prefer, but you won’t be able to correct any mistakes if you do it this way.)

uAfter a few seconds, the display shows the call’s duration in minutes and seconds.

To answer a When there’s an incoming call, Incoming Call! or the

callphone number (if you subscribe to Caller Display: see page 22) appears on the display; if the number is stored in your Phone Book (see page 17), the caller’s name may also appear.

The base unit and handset ring (unless the ringer is turned off). If you’ve stored the caller’s number as a VIP entry in the Phone Book (see page 18) and you sub- scribe to Caller Display, the handset will ring with a special melody.

◗Press any button (except the HANG UP button) to answer the call

Note — you may notice that the DECT 1915/1915+1 starts ringing a few moments after any other phone you have connected to your line. This is not a fault — it’s part of the design of the system, to enable it to receive SMS text messages.

… and if you		You can silence the ringing by pressing the left
don’t want to		Soft button to select Silent.
answer

13

Image 16

Contents DECT1915/1915+1 If you need help … Important note emergency callsUnpacking your DECT1915/1915+1 system Press the button to switch the handset on DisplayArrow buttons Left and right Soft Buttons Headset socketContents Contents Connection and conditions for useRead these notes first Installation and set-up If you have one or more charger pods … Connection to the telephone line Safety Before you startElectrical Move to a different position to clear the interferenceExploring the display To lock the keypad Shortcut buttonsPress the Hang UP button and hold it for about 2 seconds Switching on and off To switch Handset on OffVolumes Press the Hang UP button and hold it for 4 secondsYour handset’s name Idle mode Press the right Soft button to select Time and dateKey in the date as a six-digit number then select OK Display shows Time and the current timeMaking and answering calls To make a Call Key in the telephone numberPress the Phone button Don’t want to Soft button to select Silent AnswerVolume Press the or button You can mute the microphone so the personOn the other end can’t hear you To mute and un-mute the microphonePress the left Soft button Redial Last Number Redial … and options Redial listDisplay shows a list of up to 10 numbers Cancel without deleting the entry Back to cancelIf you’ve selected Delete entry, you’ll be Press the right Soft button OK to deletePhone Book memory dialling To open Phone Book To store a NumberPress the right Soft button twice Menu V OK Press the right Soft button OKKey in the phone numbers, using the numbered buttons Clear to clear characters from the displayUse the or button to go to H M or O Use the or button to go toIdle mode Display showsPress the short-cut button Display shows a list of namesDisplay shows the Phone Book entry Display goes back to the Phone Book options menuOr the left Soft button Back to cancel To idle modeTo to idle mode To delete aCaller Display Press the button Press the or button to scroll between new recordsIf you select Delete all, you’ll be asked If you select Delete entry, you’ll be askedDisplay shows the new Phone Book entry Using a multi-handset system Line at once. If you try to make a call while anotherDisplay a list of handset numbers Key in a handset numberTo transfer a Wait for the other user to answerPress the Hang UP button to hang up Transfer the callPress the right Soft button Conf Press the Handset Locator button on the base unitHandset registration To register To an extraBase unit Without a tick To de-register Press the right Soft button Menu, thenWith which it can best set up a radio link To select aBase unit manually You don’t need this function if you haveHandset registration SMS text messaging read this first ServiceSMS 01983391 All messagesIt’s important to leave these numbers as they are. If They’ve been accidentally changed, you’ll need toDisplay shows Enter Message SMS text messagingWrite your message Display shows Send Message Display shows Enter Tel NoDisplay shows Send For a few momentsTo read your MessagesDisplayed above the left Soft button Or press the left Soft button SMS to go… or to delete Messages from the Inbox Press the right Soft button OK to send the message Display shows the number of the person who sent the messageYou’ll be asked Are you sure? Scroll to Settings and press the right Soft To check orChange Button OK to select itQuick reference guide to the menus SeeTo change the way the handset is configured To set the handset so that a given number is auto To set a PIN code for the handset. By default,Incoming call by simply lifting the handset. If you Not just your individual handset To bar prevent certain typesTo bar outgoing calls to phone Numbers starting with specifiedFirst number has been preset to 000 for To change the length of the Flash To use your handset as a stopwatch timer Set Default To return all system settings to their defaultsTo view a calendar Engineers. Never attempt any repairs or adjustments TroubleshootingEveryday use Out of range. Now I can’t use my handset Display feature There is interFerence Noise onUsing a multi-handset system SMS text messagingSend TerminalBatteries PBX use If the fault persists … Cleaning and care Technical details Index Last Number Redial, 15 on a PBX Locking the keypadIndex Warranty Buttons to press for text characters Y z Y Z