Uniden DECT1915+1 manual Batteries

Page 54

Troubleshooting

If you route your calls through a different service provider from the one which supplies your line, it’s possible that this could cause problems.

“I can’t receive If there’s a problem with receiving text messages on text messages.” your phone, they will arrive as spoken messages — the

network provider Message Centre will call you and you’ll be told how to listen to your messages. Here’s what to do:

1Check that the Receive phone number in your

DECT 1915/1915+1 has not been accidentally changed. Use the steps listed on page 38 to check the number, and correct it if necessary. It should be 01983391 and the Terminal number should be 0.

2New SMS messages will not be stored if message boxes are full.

Delete old messages from inbox, outbox or draft box to allow new messages to be received.

Batteries

“The handset‘s Before you first used the handset, you should have left it battery pack is on the base unit or charger pod for up to 15 hours to

running low charge the batteries fully.

within an You may need to replace the batteries (see overleaf). hour or two.”

Clean the battery charging contacts with a dry cloth.

Check the connections between the base unit and the mains power socket.

51

Image 54
Contents DECT1915/1915+1 Important note emergency calls If you need help …Unpacking your DECT1915/1915+1 system Arrow buttons Left and right Soft Buttons Press the button to switch the handset onDisplay Headset socketContents Contents Connection and conditions for useRead these notes first Installation and set-up If you have one or more charger pods … Connection to the telephone line Electrical SafetyBefore you start Move to a different position to clear the interferenceExploring the display Shortcut buttons To lock the keypadPress the Hang UP button and hold it for about 2 seconds Volumes Switching on and offTo switch Handset on Off Press the Hang UP button and hold it for 4 secondsYour handset’s name Key in the date as a six-digit number then select OK Idle mode Press the right Soft button to selectTime and date Display shows Time and the current timePress the Phone button Making and answering callsTo make a Call Key in the telephone number Don’t want to Soft button to select Silent AnswerOn the other end can’t hear you Volume Press the or buttonYou can mute the microphone so the person To mute and un-mute the microphoneLast Number Redial … and options Redial list Press the left Soft button RedialDisplay shows a list of up to 10 numbers If you’ve selected Delete entry, you’ll be Cancel without deleting the entryBack to cancel Press the right Soft button OK to deletePress the right Soft button twice Menu V OK Phone Book memory diallingTo open Phone Book To store a Number Press the right Soft button OKUse the or button to go to H M or O Key in the phone numbers, using the numbered buttonsClear to clear characters from the display Use the or button to go toPress the short-cut button Idle modeDisplay shows Display shows a list of namesDisplay shows the Phone Book entry Display goes back to the Phone Book options menuTo to idle mode Or the left Soft button Back to cancelTo idle mode To delete aCaller Display Press the button Press the or button to scroll between new recordsIf you select Delete entry, you’ll be asked If you select Delete all, you’ll be askedDisplay shows the new Phone Book entry Display a list of handset numbers Using a multi-handset systemLine at once. If you try to make a call while another Key in a handset numberPress the Hang UP button to hang up To transfer aWait for the other user to answer Transfer the callPress the right Soft button Conf Press the Handset Locator button on the base unitHandset registration Base unit Without a tick To de-register To registerTo an extra Press the right Soft button Menu, thenBase unit manually With which it can best set up a radio linkTo select a You don’t need this function if you haveHandset registration Service SMS text messaging read this firstSMS It’s important to leave these numbers as they are. If 01983391All messages They’ve been accidentally changed, you’ll need toSMS text messaging Display shows Enter MessageWrite your message Display shows Send Display shows Send MessageDisplay shows Enter Tel No For a few momentsDisplayed above the left Soft button To read yourMessages Or press the left Soft button SMS to go… or to delete Messages from the Inbox Display shows the number of the person who sent the message Press the right Soft button OK to send the messageYou’ll be asked Are you sure? Change Scroll to Settings and press the right SoftTo check or Button OK to select itQuick reference guide to the menus SeeTo change the way the handset is configured To set a PIN code for the handset. By default, To set the handset so that a given number is autoIncoming call by simply lifting the handset. If you To bar outgoing calls to phone Not just your individual handsetTo bar prevent certain types Numbers starting with specifiedFirst number has been preset to 000 for To change the length of the Flash Set Default To return all system settings to their defaults To use your handset as a stopwatch timerTo view a calendar Troubleshooting Engineers. Never attempt any repairs or adjustmentsEveryday use Out of range. Now I can’t use my handset Ference Display featureThere is inter Noise onSend Using a multi-handset systemSMS text messaging TerminalBatteries PBX use If the fault persists … Cleaning and care Technical details Index Last Number Redial, 15 on a PBX Locking the keypadIndex Warranty Buttons to press for text characters Y z Y Z