Uniden EXI3965 manual Choose the dialing mode, Base Setting only

Page 11

D. Choose the dialing mode

Most phone systems use tone dialing, which sends DTMF tones through the phone lines. However, some phone systems still use pulse dialing such as in rural areas. The default setting is tone dialing. Depending on your dialing system, set the mode as follows:

Base Setting only

1	Press and hold flash until you hear a confirmation tone.
2	To set the dial mode for pulse dialing, press				# . Or to set the dial
	mode for tone dialing, press			. A confirmation tone sounds to

	indicate the setting is complete.

•If you are not sure of your dialing system, set for tone dialing. Make a trial call. If the call connects, leave the setting as is, otherwise set for pulse dialing.

•If your phone system requires pulse dialing and you need to send the DTMF tones for certain situations during a call, you may “switch-over” to tone dialing (refer to “Tone Dialing Switch-over” on page 31).

note

Make sure your battery pack is fully charged before choosing the dial mode.

G E T T I N G S T A R T E D

G E T T I N G S TA R T E D [ 9 ]

Image 11

Contents Page Page Contents Terminology FeaturesFlash Controls and FunctionsO N T R O L S a N D F U N C T I O N S Checking the Package Contents Choose the best location Setting up the PhoneDo the following steps Low battery alert Install the battery packBattery use time per charge Connect the base unit Press and hold flash until you hear a confirmation tone Choose the dialing modeBase Setting only Standard wall plate mounting Setting the handset retainer clip for wall mountingDirect wall mounting Setting Caller ID Options You subscribe Press Or Cidcw Off depending upon the type of service to whichWhen the phone is in the standby mode, press menu Use To move the pointer between Auto Talk On orBase ringer volume setting Ringer Volume SetupHandset Ringer Tone Setting Handset ringer volume settingPress int’cm/select and a confirmation tone will sound Distinctive Ringer SetupThen press ª to move the pointer to Use To select Distinctive On orScreen appears Int’cm/select to select. The Language settingSelecting a Language To move the pointer to LanguageHandset Off the Base Making and Receiving CallsFrom the Handset From the Base Handset On the Base Base Volume Call Waiting Adjusting Earpiece VolumeRedialing a Call Redialing from Standby ModeRedial from Talk Mode To call the last number dialed from the base Press talk key Traveling Out-of-RangeFrom the Base Store Name appears on the display. Then use the number With the handsetPress , ª to move pointer to memory location of your choice To select locationE M O R Y D I a L I N G With the Base Memory dialing from Standby ModeMaking Calls with Memory Dialing Press talk . Talk Memory dialing from Talk ModeDisplay a Programmed Number while in Memory Location List Location. Then press to select location to be edited To selectPress , ª to scroll through memory locations Press to move the pointer to Yes Editing a stored Name, Phone Number or Distinctive RingDeleting the Stored Data With the Base Press On the base unit To initiate the 3-way conversation When speaking on the handsetWhen speaking on the base Way ConferencingBase. The handset beeps. If no answer, press Intercom/page FeatureIntercom from the base to handset Intercom from the handset to baseTo Transfer from the Base to the Handset Call Transfer FeatureChain Dialing To Transfer from the Handset to the BaseSelecting a Different Channel Tone Dialing Switch-overMute Handset/Base Caller ID When the Telephone RingsYou must subscribe to Caller ID service to use this feature Press caller id to return to standby When you answer the call, the display changes to TalkViewing the Caller ID Message List Deleting a Caller ID message When the pointer is at YesWhen the pointer is at No Deleting Information from the Caller ID ListTone sounds and all stored Caller ID messages are deleted Using the Caller ID ListDeleting all Caller ID names/numbers Calling a party from the Caller ID listStoring Caller ID messages in Memory dialing Long Distance calls and Area Code setting/cancellationCurrent telephone call, the phone number Using Caller ID on Call Waiting ServiceWhen a new incoming call arrives during your For example Call Waiting Deluxe FeaturesWhile the handset is emitting the paging Changing the Digital Security CodeRemove the handset from the base unit Press and hold int’cm/page on the baseTo remove the Face plate To attach the Face plate Headset InstallationChanging the Face Plate Maintenance Installing the BeltclipPower Failure Battery replacement and handlingSymptom TroubleshootingAC Adapter Information Battery InformationGeneral Information Precautions Installation Considerations K, L IndexMemo At Uniden, we’ll take care of you