Uniden EXI3965 manual Direct wall mounting

Page 13

Direct wall mounting

If you don't have a standard wall plate, you can mount your phone directly to the wall. Before doing this, consider the following:

•Avoid electrical cables, pipes, or other items behind the mounting location that could cause a hazard when inserting screws into the wall.

•Try to mount your phone within 5 feet of a working phone jack to avoid excessive cord lengths.

•Make sure the wall material is capable of supporting the weight of the base and handset.

•Use #10 screws (minimum length of 1-3/8 inches) with anchoring devices suitable for the wall material where the base unit will be placed.

1 Insert two mounting screws into the wall, (with their appropriate anchoring device), 3-15/16 inches apart. Allow about 1/8 of an inch between the wall and screw heads for mounting the phone.

2 Set the retainer clip if necessary.

3 Refer to steps 1 through 4 on page 10 to mount the telephone.

G E T T I N G S TA R T E D [ 11 ]

G E T T I N G S T A R T E D

Image 13

Contents Page Page Contents Terminology FeaturesFlash Controls and FunctionsO N T R O L S a N D F U N C T I O N S Checking the Package Contents Do the following steps Setting up the PhoneChoose the best location Battery use time per charge Install the battery packLow battery alert Connect the base unit Base Setting only Choose the dialing modePress and hold flash until you hear a confirmation tone Standard wall plate mounting Setting the handset retainer clip for wall mountingDirect wall mounting Setting Caller ID Options When the phone is in the standby mode, press menu Or Cidcw Off depending upon the type of service to whichUse To move the pointer between Auto Talk On or You subscribe PressHandset Ringer Tone Setting Ringer Volume SetupHandset ringer volume setting Base ringer volume settingThen press ª to move the pointer to Distinctive Ringer SetupUse To select Distinctive On or Press int’cm/select and a confirmation tone will soundSelecting a Language Int’cm/select to select. The Language settingTo move the pointer to Language Screen appearsFrom the Handset From the Base Handset On the Base Making and Receiving CallsHandset Off the Base Base Volume Call Waiting Adjusting Earpiece VolumeRedial from Talk Mode Redialing from Standby ModeRedialing a Call From the Base Traveling Out-of-RangeTo call the last number dialed from the base Press talk key Press , ª to move pointer to memory location of your choice With the handsetTo select location Store Name appears on the display. Then use the numberE M O R Y D I a L I N G Making Calls with Memory Dialing Memory dialing from Standby ModeWith the Base Display a Programmed Number while in Memory Location List Memory dialing from Talk ModePress talk . Talk Press , ª to scroll through memory locations To selectLocation. Then press to select location to be edited Deleting the Stored Data Editing a stored Name, Phone Number or Distinctive RingPress to move the pointer to Yes With the Base When speaking on the base When speaking on the handsetWay Conferencing Press On the base unit To initiate the 3-way conversationIntercom from the base to handset Intercom/page FeatureIntercom from the handset to base Base. The handset beeps. If no answer, pressChain Dialing Call Transfer FeatureTo Transfer from the Handset to the Base To Transfer from the Base to the HandsetMute Handset/Base Tone Dialing Switch-overSelecting a Different Channel You must subscribe to Caller ID service to use this feature When the Telephone RingsCaller ID Viewing the Caller ID Message List When you answer the call, the display changes to TalkPress caller id to return to standby When the pointer is at No When the pointer is at YesDeleting Information from the Caller ID List Deleting a Caller ID messageDeleting all Caller ID names/numbers Using the Caller ID ListCalling a party from the Caller ID list Tone sounds and all stored Caller ID messages are deletedStoring Caller ID messages in Memory dialing Long Distance calls and Area Code setting/cancellationWhen a new incoming call arrives during your Using Caller ID on Call Waiting ServiceCurrent telephone call, the phone number For example Call Waiting Deluxe FeaturesRemove the handset from the base unit Changing the Digital Security CodePress and hold int’cm/page on the base While the handset is emitting the pagingChanging the Face Plate Headset InstallationTo remove the Face plate To attach the Face plate Maintenance Installing the BeltclipPower Failure Battery replacement and handlingSymptom TroubleshootingGeneral Information Battery InformationAC Adapter Information Precautions Installation Considerations K, L IndexMemo At Uniden, we’ll take care of you