Panasonic AJ-HD1200A Releasing the menu protection mode, Displaying the Diag menu

Page 27

Setup (initial settings)

5 Set the LOCAL/MENU/REMOTE switch to the LOCAL or REMOTE position.

The unit is now set to the menu protection mode. When the LOCAL/MENU/REMOTE switch is set to the MENU position, the unit is not set to the menu setting mode, and “MENU PROTECTED” appears on the video monitor screen.

<Note>

If, during the setting of the menu protection mode, the LOCAL/MENU/REMOTE switch is set to the MENU position while the COUNTER button on the front panel is held down, the unit is set to the menu setting mode, and the regular menu settings can be performed.

Perform steps 2 to 7 of “Setting method using the on-screen menus.”

Releasing the menu protection mode

1 Set the LOCAL/MENU/REMOTE switch to the MENU position while holding down the COUNTER button on the front panel.

The unit is set to the menu setting mode, and the menu screen appears on the video monitor.

2 Perform steps 2 and 3 of the menu protection procedure described above.

The screen prompting the user to confirm whether to initiate menu protection appears on the video monitor.

MENU PROTECT OK?

2NO YES

3 Press the MENU-UP button or MENU-DOWN button to move the cursor to the NO position, and press the SET button.

The menu protection mode is now released.

Displaying the DIAG menu

The unit comes with a function for displaying the “hour meter,” “software version” and “deck serial No.” on the video monitor.

1 Set the LOCAL/MENU/REMOTE switch to the MENU position while holding down the EJECT button.

The unit is set to the DIAG display mode, and the hour meter and deck serial No. appear on the video monitor.

DIAG–MENU HOURS METER

Ser	222222222
H00	OPERATION	00000H
H01	DRUM RUN	00000H
H02	TAPE RUN	00000H
H03	THREADING	00000T
H04	F LOADING	00000T
H11	DRUM RUN r	00000H
H12	TAPE RUN r	00000H
H13	THREADING r	00000T
H14	F LOADING r	00000T

Items with “r” can be reset when the unit is serviced.

2 With the hour meter displayed, press the SEARCH button.

The software version appears on the video monitor.

DIAG–MENU SOFT VERSION

SYSIF 1.22-22-2.22

AVDV 1.22-22-2.22

SERVO 1.22-22-2.22

END

The hour meter display is restored when the SEARCH button is pressed again.

3 Set the LOCAL/MENU/REMOTE switch to the LOCAL or REMOTE position.

The unit is restored to its regular mode.

27

Image 27

Contents Model No. AJ- P Operating InstructionsOperating precaution For your safetyDo not Remove Cover or Back Contents Introduction FeaturesMulti-functional interfaces Front panel Parts and their functionsSCH lamp2 LOCAL/MENU/REMOTE switchRepeat lamp System format lampAudio output lamps CH12, CH34 Audio monitor selector switch? Analog lamp2 @ Meter button and lamp CH34Headphone jack Analog audio signal recording level controls2Volume control 720p lampReset button REC button2 No optional board installedWhen the AJ-YA120AG or AJ-YAD120AG is installed TAPE/EE switchDC OUT socket Rear panelAC in inlet DC in socketAudio in connectors CH1, CH2, CH3, CH42 TC in connector2TC OUT connector HD/SD REF Video in connectors and 75Ω termination switch2Usable tapes Precautions for using consumer DV and Dvcam cassettesTapes Inserting the tapeTurning on the unit’s power Stop modeOperation Pause/recording follow-on recording RecordingInsert a cassette tape into the unit Press the Play button PlaybackCue/review Still image playbackWhen AJ-A95 is connected Linear 0.3k playbackVariable speed playback Repeat playback Setting the Begin and END pointsSetting the repeat playback mode Set the VTR to the menu modeUser’s bit Setting the time codeTime code & user’s bit Time codeT2R00 07 04 Setting the user’s bitSelect menu item No.531 UB Preset Playing back the time code and user’s bitDisplay position Superimposed screen displaysCharacters displayed Remaining tape displayM mode Operation modeTime mode STA modeSet the LOCAL/MENU/REMOTE switch to the Menu position Setup initial settingsSetting method using the on- screen menus Returning to the factory settingsSetting the user defaults Menu protection Loading the user defaultsReleasing the menu protection mode Displaying the Diag menuWith the hour meter displayed, press the Search button Menus which are displayed Setup menusTYPE-B Near Audio in SEL Indicates the factory setting Setting Description of settings Superimposed DisplaySystem Setting Description of settings System FreqHD SYS H ADV Basic Format Display Auto SYS FormatPB Format ManualFormats for playback 022 020 023 Playback formatManual Dvcam HD-LP Operation Auto REW FRZ Mode SELSP Mode INH Memory ModeTC BGN Rept ModeBattery SEL CTL BGNTape Protect InterfaceTime Code UB Preset Phase CorrDF Mode TC PresetVideo CC F1 Blank VO Setup HDVO Setup SD BLK ClipSDI Index ESR Mode SDCCR Mode SD EDH SDAudio CH3 REC CUECH1 CH2Menu DIF OUT CH DIF ConfigDIF Speed DIF in CHError messages Error No Error message and description23/24 Hz mode and 25 Hz mode Unload Error Operation performed by AJ-HD1200A CondensationEmergency eject Video head cleaningMaintenance Procedure to ejecting the tape manually in an emergencyGeneral Specifications$ Video input connectors21 $ Video output connectorsOptions Other ConnectorsGovernment Marketing Department Executive OfficeSoutheast Region Central Region