Panasonic AJ-HD1200A operating instructions Other Connectors, Options

Page 55

Specifications

$ Video output adjustment ranges

HD serial digital output system phase21:

1080i: ±0.5H (in 13.5ns increments)

59/60 Hz:

±1100 samples

50 Hz:

±1320 samples

23/24 Hz:

±1375 samples

720p: ±0.5H (in 13.5ns increments) 59/60 Hz: ±825 samples

SD serial digital/composite video output system phase21:

±0.5H (in 37ns increments) 59 Hz: ±858 samples

50 Hz: ±864 samples

Composite video output SC phase; ±180 deg. or more

[AUDIO]

$ Digital audio

Sampling frequency:

48 kHz (synchronized with video)

Quantizing:

16 bits

Frequency response:

20 Hz to 20 kHz ±1 dB (at reference level)

Dynamic range:

More than 85 dB (1 kHz, emphasis OFF)

Distortion:

Less than 0.1% (1 kHz, emphasis OFF, reference level)

Crosstalk:

Less than –80 dB (1 kHz, between 2 channels)

Wow & flutter:

Below measurable limits

Headroom:

20 dB

$ Audio input connectors21

Analog input (CH1, CH2, CH3, CH4):

XLR k4, 600 Ω/high impedance switchable (default: 600 Ω)

+4/0/–20 dBm/–60 dBu switchable

(The impedance is set to 3 kΩ when –60 dB is selected)

HD serial digital input:

BNC k1, 75 Ω,

Compliant with SMPTE 292M/296M/299M standard

$ Audio output connectors

Analog output (CH1, CH2, CH3, CH4):

XLR k4, low impedance

+4/0/–20 dBm (with 600 Ω load) switchable Monitor output L or R switchable for CH3/CH4 output

HD serial digital output21:

BNC k2, 75 Ω

(compliant with SMPTE 292M/296M/299M standard)

SD serial digital output21:

BNC k1, 75 Ω

(compliant with SMPTE 259M-C/272M-A, ITU-R BT.656-4 standards)

Monitor output (L, R):

PHONO k2, 600 Ω, –8 dBv

Headphone output:

Stereo (6 mm diameter), 8 Ω, level variable

[OTHER CONNECTORS]

Time code input21:

BNC k1, 0.5 to 8V [p-p], 10 kΩ

Time code output:

BNC k1, low impedance, 2.0 ±0.5 V [p-p] (with 600 Ω load)

RS-422A input:

D-sub 9-pin, for AJ-A95

RS-422A interface

DC power output:

4 pins k1, DC 12 V, 250 mA, for AJ-A95

DV input/output connector:

Connector:

6-pin type Transmission rate:

400 Mbps, 200 Mbps, 100 Mbps;selectable Transmission data:

Compliant with IEEE 1394-1995 Compliant with IEC 61883-Part1, Part2

Control command:

Compliant with AV/C command set (General Ver 3.0, VCR Subunit Ver 2.01)

[OPTIONS]

HD SDI input/output SD SDI output board: AJ-YA120AG

Digital video input/output board: AJ-YAD120AG

21: This functions only when the AJ-YA120AG (optional accessory) is installed.

22: This functions only when the AJ-YAD120AG (optional accessory) is installed.

Weight and dimensions shown are approximate. Specifications are subject to change without notice.

55

Page 54 Page 56
Image 55
Page 54 Page 56
Contents Model No. AJ- P Operating InstructionsOperating precaution For your safetyDo not Remove Cover or Back Contents Introduction FeaturesMulti-functional interfaces Front panel Parts and their functionsSCH lamp2 LOCAL/MENU/REMOTE switchRepeat lamp System format lampAudio output lamps CH12, CH34 Audio monitor selector switch? Analog lamp2 @ Meter button and lamp CH34Headphone jack Analog audio signal recording level controls2Volume control 720p lampReset button REC button2 No optional board installedWhen the AJ-YA120AG or AJ-YAD120AG is installed TAPE/EE switchDC OUT socket Rear panelAC in inlet DC in socketAudio in connectors CH1, CH2, CH3, CH42 TC in connector2TC OUT connector HD/SD REF Video in connectors and 75Ω termination switch2Usable tapes Precautions for using consumer DV and Dvcam cassettesTapes Inserting the tapeStop mode Turning on the unit’s powerOperation Pause/recording follow-on recording RecordingInsert a cassette tape into the unit Press the Play button PlaybackCue/review Still image playbackLinear 0.3k playback When AJ-A95 is connectedVariable speed playback Repeat playback Setting the Begin and END pointsSetting the repeat playback mode Set the VTR to the menu modeUser’s bit Setting the time codeTime code & user’s bit Time codeT2R00 07 04 Setting the user’s bitSelect menu item No.531 UB Preset Playing back the time code and user’s bitDisplay position Superimposed screen displaysCharacters displayed Remaining tape displayM mode Operation modeTime mode STA modeSet the LOCAL/MENU/REMOTE switch to the Menu position Setup initial settingsSetting method using the on- screen menus Returning to the factory settingsSetting the user defaults Menu protection Loading the user defaultsDisplaying the Diag menu Releasing the menu protection modeWith the hour meter displayed, press the Search button Menus which are displayed Setup menusTYPE-B Near Audio in SEL Setting Description of settings Superimposed Display Indicates the factory settingSystem System Freq Setting Description of settingsHD SYS H ADV Basic Format Display Auto SYS FormatPB Format Manual022 020 023 Playback format Formats for playbackManual Dvcam HD-LP Operation Auto REW FRZ Mode SELSP Mode INH Memory ModeTC BGN Rept ModeBattery SEL CTL BGNTape Protect InterfaceTime Code UB Preset Phase CorrDF Mode TC PresetVideo CC F1 Blank VO Setup HDVO Setup SD BLK ClipSDI Index ESR Mode SDCCR Mode SD EDH SDAudio CH3 REC CUECH1 CH2Menu DIF OUT CH DIF ConfigDIF Speed DIF in CHError No Error message and description Error messages23/24 Hz mode and 25 Hz mode Unload Error Operation performed by AJ-HD1200A CondensationEmergency eject Video head cleaningMaintenance Procedure to ejecting the tape manually in an emergencyGeneral Specifications$ Video input connectors21 $ Video output connectorsOptions Other ConnectorsGovernment Marketing Department Executive OfficeSoutheast Region Central Region
Top Page Image Contents