Panasonic AJ-HD1200A operating instructions System, Indicates the factory setting

Page 31

Setup menus

SYSTEM

 

Item

 

Setting

 

 

 

 

 

Description of settings

No.

Superimposed

No.

Superimposed

 

display

display

 

 

 

 

 

 

 

 

 

 

 

 

 

 

12

SYS H (HD)

0000

–1100

For adjusting the system phase of the HD SDI output signals (in 13.5 ns

 

 

:

:

increments).

 

 

1100

0

–: The phase is advanced.

 

 

:

:

+: The phase is delayed.

 

 

2200

1100

<Note>

 

 

 

 

The setting range is as follows:

 

 

 

 

O –1320 to 0 to 1320 when 50i/25P, 25 (HD) or 25 (SD) is selected as the

 

 

 

 

SYSTEM FREQ setting

 

 

 

 

O –1375 to 0 to 1375 when 23/24 is selected as the SYSTEM FREQ setting

 

 

 

 

 

14

SYS SC (SD)

0000

–108

For adjusting the system phase of the VIDEO output and SD SDI output signals

 

 

:

:

(total variable range of over ±180 degrees).

 

 

0108

0

–: The phase is advanced.

 

 

:

:

+: The phase is delayed.

 

 

0216

108

 

 

 

 

 

 

15

VO SYS H (SD)

0000

–858

For adjusting the system phase of the VIDEO output signals (in 37 ns increments).

 

 

:

:

–: The phase is advanced.

 

 

0858

0

+: The phase is delayed.

 

 

:

:

<Note>

 

 

1716

858

The setting range is –864 to 0 to 864 when 50i/25P, 25 (HD) or 25 (SD) is selected

 

 

 

 

as the menu item No.25 [SYSTEM FREQ] setting.

 

 

 

 

 

16

SD SYS H (SD)

0000

–858

For adjusting the system phase of the SD SDI output signals (in 37 ns increments).

 

 

:

:

–: The phase is advanced.

 

 

0858

0

+: The phase is delayed.

 

 

:

:

<Note>

 

 

1716

858

The setting range is –864 to 0 to 864 when 50i/25P, 25 (HD) or 25 (SD) is selected

 

 

 

 

as the menu item No.25 [SYSTEM FREQ] setting.

 

 

 

 

 

18

SCH COAR (SD)

0000

0

For adjusting the SCH (sub-carrier to horizontal) phase of the VIDEO output

 

 

0001

90

signals (4 positions in 90-degree increments).

 

 

0002

180

The SC phase changes, and the H phase remains unchanged.

 

 

0003

270

 

 

 

 

 

 

19

SCH FINE (SD)

0000

–32

For adjusting the SCH (sub-carrier to horizontal) phase of the VIDEO output

 

 

:

:

signals (variable range of over ±45 degrees).

 

 

0032

0

The SC phase changes, and the H phase remains unchanged.

 

 

:

:

A range of ±180 degrees is covered by using this setting in combination with item

 

 

0064

32

No.18 [SCH COAR(SD).

 

 

 

 

 

20

AV PHASE

0000

–100

For adjusting the phase of the AUDIO output signals in relation to the VIDEO

 

 

:

:

output signals (in 20.8 µs increments).

 

 

0100

0

–: The phase of the audio output signals is advanced in relation to the video output

 

 

:

:

signals.

 

 

0200

100

+: The phase of the audio output signals is delayed in relation to the video output

 

 

 

 

signals.

 

 

 

 

 

” indicates the factory setting.

31

Image 31
Contents Model No. AJ- P Operating InstructionsOperating precaution For your safetyDo not Remove Cover or Back Contents Introduction FeaturesMulti-functional interfaces Front panel Parts and their functionsSCH lamp2 LOCAL/MENU/REMOTE switchRepeat lamp System format lampAudio output lamps CH12, CH34 Audio monitor selector switch? Analog lamp2 @ Meter button and lamp CH34Headphone jack Analog audio signal recording level controls2Volume control 720p lampReset button REC button2 No optional board installedWhen the AJ-YA120AG or AJ-YAD120AG is installed TAPE/EE switchDC OUT socket Rear panelAC in inlet DC in socketAudio in connectors CH1, CH2, CH3, CH42 TC in connector2TC OUT connector HD/SD REF Video in connectors and 75Ω termination switch2Usable tapes Precautions for using consumer DV and Dvcam cassettesTapes Inserting the tapeStop mode Turning on the unit’s powerOperation Pause/recording follow-on recording RecordingInsert a cassette tape into the unit Press the Play button PlaybackCue/review Still image playbackLinear 0.3k playback When AJ-A95 is connectedVariable speed playback Repeat playback Setting the Begin and END pointsSetting the repeat playback mode Set the VTR to the menu modeUser’s bit Setting the time codeTime code & user’s bit Time codeT2R00 07 04 Setting the user’s bitSelect menu item No.531 UB Preset Playing back the time code and user’s bitDisplay position Superimposed screen displaysCharacters displayed Remaining tape displayM mode Operation modeTime mode STA modeSet the LOCAL/MENU/REMOTE switch to the Menu position Setup initial settingsSetting method using the on- screen menus Returning to the factory settingsSetting the user defaults Menu protection Loading the user defaultsDisplaying the Diag menu Releasing the menu protection modeWith the hour meter displayed, press the Search button Menus which are displayed Setup menusTYPE-B Near Audio in SEL Setting Description of settings Superimposed Display Indicates the factory settingSystem System Freq Setting Description of settingsHD SYS H ADV Basic Format Display Auto SYS FormatPB Format Manual022 020 023 Playback format Formats for playbackManual Dvcam HD-LP Operation Auto REW FRZ Mode SELSP Mode INH Memory ModeTC BGN Rept ModeBattery SEL CTL BGNTape Protect InterfaceTime Code UB Preset Phase CorrDF Mode TC PresetVideo CC F1 Blank VO Setup HDVO Setup SD BLK ClipSDI Index ESR Mode SDCCR Mode SD EDH SDAudio CH3 REC CUECH1 CH2Menu DIF OUT CH DIF ConfigDIF Speed DIF in CHError No Error message and description Error messages23/24 Hz mode and 25 Hz mode Unload Error Operation performed by AJ-HD1200A CondensationEmergency eject Video head cleaningMaintenance Procedure to ejecting the tape manually in an emergencyGeneral Specifications$ Video input connectors21 $ Video output connectorsOptions Other ConnectorsGovernment Marketing Department Executive OfficeSoutheast Region Central Region