Sharp MD X5 HOW to USE the BUILT-IN Timer, Timer playback, Programming for timer playback

Page 30

HOW TO USE THE BUILT-IN TIMER

 

ENTER

 

TIMER/

 

DELETE

1

6

2

 

3

 

4

7

 

 

8

5

9

 

HTimer playback

Before timer playback, the following preparations are required.

IMake sure that the clock setting is correct. (Page 8)

ILoad a CD or a MD.

IPreset the radio station. (Page 12)

Programming for timer playback:

1 While in the stop mode, press the TIMER/DELETE button and then the

▲or ▼ button so that the TIMER SET display appears.

2 Within 10 seconds, press the ENTER button, and then select the timer mode using the ▲ or ▼ button.

3 Press the ENTER button.

IThe start time setting display will appear.

4 Enter the hour for the start time using the 1 or 0 button. Then, press the ENTER button.

5 Enter the minute using the 1 or 0 button. Then, press the ENTER button.

IThe stop time setting display will appear.

IThe display time will increase by one hour automatically.

6 Enter the hour for the stop time using the 1 or 0 button. Then, press the ENTER button.

7 Enter the minute using the 1 or 0 button. Then, press the ENTER button.

IThe start and stop times are now set.

8 Select the source program using the 1 or 0 button.

IThe source is selected in the following sequence:

MD → CD → TUNER → AUX → DIGITAL1 → DIGITAL2 → PHONO

→

IIf TUNER is selected, press the ENTER button, and then select the preset number using the 1 or 0 button.

9 Press the ENTER button.

10 Adjust the volume level using the 1 or 0 button.

11 Press the ENTER button.

ITimer playback setting is complete.

Note:

IIf you do not perform the next operation within 10 seconds, the operation will be canceled. If this happens, try the operation again from the beginning.

Setting timer playback:

1 Press the TIMER/DELETE button.

IPress the ▲ or ▼ button so that the T-STANDBY display appears.

2 Press the ENTER button.

IThe settings will appear in order, and the unit will enter the timer playback standby mode. (If the power is on, the unit will be turned off.)

1

2

3 When the timer playback start time is reached, the power will be turned on and the volume will gradually increase to the preset position.

When the timer playback stop time is reached, the power will be turned off automatically.

Notes:

IWhen the CD or MD is played to the end, playback will stop before the stop time.

If you wish to play to the stop time, set repeat play for the CD or MD.

IThe timer playback with this unit cannot be used to control equipment connected to this unit. You must use the timer of the other equipment, if it has one.

IThe timer playback and timer recording functions cannot be used at the same time.

29

*22-34

29

98.6.23, 10:11 AM

Page 29 Page 31
Image 30
Page 29 Page 31
Contents A0004CONTENTS AccessoriesModel Important Safeguards Special NotesPrecautions Names of Controls and Indicators Display windowFront panel Rear panel Speaker sectionTweeter Woofer Speaker Cord Speaker connection Preparation for USEAntenna connection Placing the systemPrecautions for battery use Connecting the AC power cordLoading the batteries for the remote control To change the brightness of the displayPre-programmed equalizer VolumeSound Control Extra bass X-BASSSetting the Clock To change the settingTo check the date and time Compact Disc Operation Loading and playing CDsMinidisc Operation Loading and playing MiniDiscsTo remove a MiniDisc Manual tuning TuningAuto tuning Radio OperationPreset tuning To recall a preset stationTo select preset numbers 11 to Direct-selection play CD and MD OperationsCue and review Apss Auto Program Search SystemAutomatic Programmable Music Selector See the diagram to the left Switching the time displayTo cancel repeat playback or random play Random and repeat playInformation TOC to be recorded on an MD Basic Information on MinidiscsDifferences from tape recordings About track numbersAbout monaural long-play mode RecordingRecording from a CD onto a MiniDisc One-Touch Editing To rerecord Recording from the built-in radio onto a MiniDisc To interrupt recordingTo record the track number during recording Editing Using the editing function Edit MenuRecording the editing results When both tracks have a name To combine two noncontiguous tracksProgrammed move To erase tracks one at a time To erase all of the tracks at onceTo create a disc name To erase disc namesType Characters To erase a character To create a track nameTo erase track names To add a characterTo erase a name To change the message displayed when Power is turned offEntering Characters To erase a programmed messageCompatible keyboards To enter characters from a computer keyboardEntering characters Keys you can useProgramming for timer playback HOW to USE the BUILT-IN TimerTimer playback Setting timer playbackTimer recording Programming for timer recordingSetting timer recording To check the timer setting To cancel the timer operationTo confirm the sleep timer setting Simultaneous sleep and timer operationTo change the sleep timer To cancel the sleep operationUsing External Units Connecting external unitsConnecting to a stereo turntable Headphones What is the space-cut function? Listening to sound from an external unitRecording sound from an external unit To start a recording by yourself manual recording What is a MINIDISC? Minidisc System Limitations TroubleshootingIf a problem occurs GeneralMD recording and playback Radio receptionError messages Meaning Remedy Blank MDInternal care MaintenanceSpecifications External careMemo Calling for Service Limited WarrantySharp Plaza, Mahwah, New Jersey
Top Page Image Contents