Sharp MD X5 operation manual CD and MD Operations, Cue and review, Direct-selection play

Page 14

CD AND MD OPERATIONS

4

5

Track number

4 input buttons

5

5

4

HCue and review

1 Load a disc and begin playback.

2 Hold down the 4 button for audible fast forward, and hold down the 5 button for audible fast reverse.

3 Normal playback will resume when the 4 or 5 button is released.

Notes:

IIf the end of the disc is reached while cueing, “DISC END” will appear on the display, and operation will pause. Press the CD H or MD H button to stop operation.

When you want to listen to the disc again, press the 5 button to locate the desired track. Normal playback will start from that point.

IWhen the beginning of the first track is reached, normal playback will start.

To search very quickly

When fast forward or fast reverse is used while in the pause mode, the playback point will move more quickly than when using audible fast forward or audible fast reverse in the playback mode.

IIn this mode, no sound is heard. Therefore, you must refer to the time display.

IWhen you lift your finger, the unit will re-enter the pause mode.

HDirect-selection play

By using the track number input buttons on the remote control, any track you wish to can be played directly, by entering its number.

1 Select the desired program source, CD or MD, by pressing the CD Hor MD H button.

2 Use the track number input buttons to select the desired track number.

A. To select track numbers 11 to 99

Press the >10 button first, then press the track number. For example to select 28:

1Press the >10 button.

2Within 5 seconds, press the "2" button.

3Within 5 seconds, press the "8" button.

B. To select track number 100 or higher (only for MD)

Press the >10 button twice, then press the track number. For example to select 105:

1Press the >10 button.

2Within 5 seconds, press the >10 button.

3Within 5 seconds, press the "1" button.

4Within 5 seconds, press the "10/0" button.

5Within 5 seconds, press the "5" button.

The beginning of the selected track will be found, and play will begin automatically.

Notes:

IA track number higher than the number of tracks on the disc cannot be selected.

IDuring APMS play or random play, track number selection play is not possible.

HAPSS (Auto Program Search System)

APSS automatically locates the beginning of any track.

To listen again to the track being played:

Press the 5 button for less than 0.5 seconds during playback.

To move to the beginning of the next track:

Press the 4 button for less than 0.5 seconds during playback.

ITo skip a number of tracks at one time, press the 5 or 4 button repeatedly until the desired track number is shown.

ITo start playback from a desired track, press the 5or 4button while in the stop mode to select the track number, and then press the 06 button.

13

*01-21

13

98.6.23, 10:09 AM

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Model A0004CONTENTSAccessories Important Safeguards Special NotesPrecautions Front panel Names of Controls and IndicatorsDisplay window Tweeter Woofer Speaker Cord Rear panelSpeaker section Speaker connection Preparation for USEAntenna connection Placing the systemPrecautions for battery use Connecting the AC power cordLoading the batteries for the remote control To change the brightness of the displayPre-programmed equalizer VolumeSound Control Extra bass X-BASSTo check the date and time Setting the ClockTo change the setting Compact Disc Operation Loading and playing CDsTo remove a MiniDisc Minidisc OperationLoading and playing MiniDiscs Manual tuning TuningAuto tuning Radio OperationTo select preset numbers 11 to Preset tuningTo recall a preset station Direct-selection play CD and MD OperationsCue and review Apss Auto Program Search SystemAutomatic Programmable Music Selector See the diagram to the left Switching the time displayTo cancel repeat playback or random play Random and repeat playInformation TOC to be recorded on an MD Basic Information on MinidiscsDifferences from tape recordings About track numbersRecording from a CD onto a MiniDisc One-Touch Editing About monaural long-play modeRecording To rerecord To record the track number during recording Recording from the built-in radio onto a MiniDiscTo interrupt recording Editing Recording the editing results Using the editing functionEdit Menu When both tracks have a name To combine two noncontiguous tracksProgrammed move To erase tracks one at a time To erase all of the tracks at onceType Characters To create a disc nameTo erase disc names To erase a character To create a track nameTo erase track names To add a characterTo erase a name To change the message displayed when Power is turned offEntering Characters To erase a programmed messageCompatible keyboards To enter characters from a computer keyboardEntering characters Keys you can useProgramming for timer playback HOW to USE the BUILT-IN TimerTimer playback Setting timer playbackSetting timer recording Timer recordingProgramming for timer recording To check the timer setting To cancel the timer operationTo confirm the sleep timer setting Simultaneous sleep and timer operationTo change the sleep timer To cancel the sleep operationConnecting to a stereo turntable Using External UnitsConnecting external units Headphones Recording sound from an external unit What is the space-cut function?Listening to sound from an external unit To start a recording by yourself manual recording What is a MINIDISC? Minidisc System Limitations TroubleshootingIf a problem occurs GeneralMD recording and playback Radio receptionError messages Meaning Remedy Blank MDInternal care MaintenanceSpecifications External careMemo Sharp Plaza, Mahwah, New Jersey Calling for ServiceLimited Warranty
Top Page Image Contents