Sharp MD X5 operation manual Setting the Clock, To change the setting, To check the date and time

Page 9

SETTING THE CLOCK

 

 

ENTER

 

POWER

TIMER/

 

 

 

 

DELETE

 

2

 

 

3

 

 

4

 

 

5

 

 

6

 

 

7

 

 

8

 

 

9

 

 

10

 

 

11

 

 

12

 

 

13

 

 

14

 

 

 

8

*01-21

 

8

When you have set the date and time, this unit can be used as a clock. It can be used for timer recording or for timer playback. It is also used to store the MD recording date in memory.

1 Press the POWER button to turn the power on.

2 Press the TIMER/DELETE button.

3 Within 10 seconds, press the ▲ or ▼ button to select "TIME ADJUST".

4 Within 10 seconds, press the ENTER button.

IThe unit will enter the date setting mode.

5 Adjust the month by pressing the 1 or 0 button.

6 Press the ENTER button to set the month.

7 Adjust the day by pressing the 1 or 0 button.

8 Press the ENTER button to set the date.

9 Adjust the year by pressing the 1 or 0 button.

IPress the button once to increase or decrease the year by one. Keep pressing it to advance continuously.

IFor a year after 2000, set "00" for 2000, "01" for 2001 and so on.

10 Press the ENTER button to set the year.

IThe unit will enter the time setting mode.

11 Adjust the hour by pressing the 1 or 0 button.

IPress the button once to increase or decrease the hour by one. Keep pressing it to advance continuously.

IOn the display, midnight is shown as "12:00 AM" and noon is shown as "12:00 PM". When setting the time, be careful not to confuse AM and PM.

12 Press the ENTER button to set the hour.

13 Adjust the minute by pressing the 1 or 0 button.

IPress the button once to increase or decrease the minutes by one. When the button is held down, the time will change in increments of 5 minutes.

14 Press the ENTER button to set the minute.

IThe clock will start operating.

IWhen about 3 seconds have elapsed, the original display will reappear.

Notes:

IIn the event of a power failure or when the AC power cord is discon- nected, the clock display will go out.

When the AC power supply is restored, the clock display will flash on and off to indicate the time when the power failure occurred or when the AC power cord was disconnected.

IWhile recording an MD, you cannot set the date and clock. Be sure to set the date and clock before recording.

IThe range of dates that can be entered is from January 1, 1997 to December 31, 2049.

To change the setting:

IOnce you have set the date and time, "TIME ADJUST" will not be displayed in step 3. Press the ▲ or ▼ button to make the date and time appear.

IIf you don't need to change the settings, just press the ENTER button.

To check the date and time:

Press the TIMER/DELETE button, and press the ▲ or ▼ button until the date and time appear.

IWhen about 10 seconds have elapsed, the original display will reap- pear.

98.6.23, 10:09 AM

Page 8 Page 10
Image 9
Page 8 Page 10
Contents A0004CONTENTS AccessoriesModel Special Notes Important SafeguardsPrecautions Names of Controls and Indicators Display windowFront panel Rear panel Speaker sectionTweeter Woofer Speaker Cord Antenna connection Preparation for USESpeaker connection Placing the systemLoading the batteries for the remote control Connecting the AC power cordPrecautions for battery use To change the brightness of the displaySound Control VolumePre-programmed equalizer Extra bass X-BASSSetting the Clock To change the settingTo check the date and time Loading and playing CDs Compact Disc OperationMinidisc Operation Loading and playing MiniDiscsTo remove a MiniDisc Auto tuning TuningManual tuning Radio OperationPreset tuning To recall a preset stationTo select preset numbers 11 to Cue and review CD and MD OperationsDirect-selection play Apss Auto Program Search SystemAutomatic Programmable Music Selector To cancel repeat playback or random play Switching the time displaySee the diagram to the left Random and repeat playDifferences from tape recordings Basic Information on MinidiscsInformation TOC to be recorded on an MD About track numbersAbout monaural long-play mode RecordingRecording from a CD onto a MiniDisc One-Touch Editing To rerecord Recording from the built-in radio onto a MiniDisc To interrupt recordingTo record the track number during recording Editing Using the editing function Edit MenuRecording the editing results To combine two noncontiguous tracks When both tracks have a nameProgrammed move To erase all of the tracks at once To erase tracks one at a timeTo create a disc name To erase disc namesType Characters To erase track names To create a track nameTo erase a character To add a characterEntering Characters To change the message displayed when Power is turned offTo erase a name To erase a programmed messageEntering characters To enter characters from a computer keyboardCompatible keyboards Keys you can useTimer playback HOW to USE the BUILT-IN TimerProgramming for timer playback Setting timer playbackTimer recording Programming for timer recordingSetting timer recording To cancel the timer operation To check the timer settingTo change the sleep timer Simultaneous sleep and timer operationTo confirm the sleep timer setting To cancel the sleep operationUsing External Units Connecting external unitsConnecting to a stereo turntable Headphones What is the space-cut function? Listening to sound from an external unitRecording sound from an external unit To start a recording by yourself manual recording What is a MINIDISC? If a problem occurs TroubleshootingMinidisc System Limitations GeneralRadio reception MD recording and playbackBlank MD Error messages Meaning RemedySpecifications MaintenanceInternal care External careMemo Calling for Service Limited WarrantySharp Plaza, Mahwah, New Jersey
Top Page Image Contents