Sharp MD X5 Preparation for USE, Antenna connection, Speaker connection, Placing the system

Page 6

PREPARATION FOR USE

AM loop antenna

1	2		3
(1)		(2)
			ANTENNA
			AM
			LOOP
FM aerial			FM
FM aerial
Right speaker				Left speaker
			RATED SPEAKER
			IMPEDANCE ;	Red
			6 OHMS MIN.

			LEFT
		Black		Black
				Black
			RIGHT
		Red	SPEAKERS
1	2		3

IUnplug the AC power cord from the AC outlet before connecting or disconnecting any component.

HAntenna connection

Connect the antenna wire to the ANTENNA jack.

(1) FM antenna

Position the FM antenna wire in the direction where the stongest signal can be received.

(2) AM loop antenna

Position the AM loop antenna for optimum reception.

Place the AM loop antenna on a shelf, etc., or attach it to a stand or wall with screws (not supplied).

Notes:

IDo not place the antenna on the unit. It may result in noise generation, since the unit is equipped with digital electronics. Place the antenna away from the unit for better reception.

IIf the AM loop antenna and the FM antenna wire are placed near the AC power cord, interference may result.

HSpeaker connection

Connect each speaker wire to the SPEAKER terminals as shown.

Use speakers with an impedance of 6 ohms or more, as lower impedance speakers can damage the unit.

Cautions:

IConnect the black wire to the minus (–) terminal, and the red wire to the plus (+) terminal.

IDo not mix the right channel and left channel wiring when connecting the speakers to the unit.

IDo not let bare speaker wires touch each other as this may damage the amplifier and/or speakers.

Note:

IThe speaker grille is not removable.

Left speaker	Right speaker
For the	For the
left side	right side

HPlacing the system

IBe sure to keep space between the units for ventilation.

IKeep the back and sides of this unit at least 2" (5 cm) away from the wall.

IIf any kind of magnet or an electromagnet is placed too close to the TV set and the system, irregular color may be seen.

TV set location

IDepending on the particular location of a TV set, color variations may be seen on the TV screen. If this happens, move the system and its speakers away from the TV and turn off the TV set. After 15 - 30 minutes, turn on the TV again.

The TV's own demagnetising function should eliminate the variations. However, if the color still does not look right, move the system further away from the TV set.

Note:

IA cooling fan is built into this product to avoid heat buildup. When the power is turned on, the cooling fan will run.

5

*01-21

5

98.6.23, 10:09 AM

Image 6

Contents A0004CONTENTS AccessoriesModel Important Safeguards Special NotesPrecautions Names of Controls and Indicators Display windowFront panel Rear panel Speaker sectionTweeter Woofer Speaker Cord Speaker connection Preparation for USEAntenna connection Placing the systemPrecautions for battery use Connecting the AC power cordLoading the batteries for the remote control To change the brightness of the displayPre-programmed equalizer VolumeSound Control Extra bass X-BASSSetting the Clock To change the settingTo check the date and time Compact Disc Operation Loading and playing CDsMinidisc Operation Loading and playing MiniDiscsTo remove a MiniDisc Manual tuning TuningAuto tuning Radio OperationPreset tuning To recall a preset stationTo select preset numbers 11 to Direct-selection play CD and MD OperationsCue and review Apss Auto Program Search SystemAutomatic Programmable Music Selector See the diagram to the left Switching the time displayTo cancel repeat playback or random play Random and repeat playInformation TOC to be recorded on an MD Basic Information on MinidiscsDifferences from tape recordings About track numbersAbout monaural long-play mode RecordingRecording from a CD onto a MiniDisc One-Touch Editing To rerecord Recording from the built-in radio onto a MiniDisc To interrupt recordingTo record the track number during recording Editing Using the editing function Edit MenuRecording the editing results When both tracks have a name To combine two noncontiguous tracksProgrammed move To erase tracks one at a time To erase all of the tracks at onceTo create a disc name To erase disc namesType Characters To erase a character To create a track nameTo erase track names To add a characterTo erase a name To change the message displayed when Power is turned offEntering Characters To erase a programmed messageCompatible keyboards To enter characters from a computer keyboardEntering characters Keys you can useProgramming for timer playback HOW to USE the BUILT-IN TimerTimer playback Setting timer playbackTimer recording Programming for timer recordingSetting timer recording To check the timer setting To cancel the timer operationTo confirm the sleep timer setting Simultaneous sleep and timer operationTo change the sleep timer To cancel the sleep operationUsing External Units Connecting external unitsConnecting to a stereo turntable Headphones What is the space-cut function? Listening to sound from an external unitRecording sound from an external unit To start a recording by yourself manual recording What is a MINIDISC? Minidisc System Limitations TroubleshootingIf a problem occurs GeneralMD recording and playback Radio receptionError messages Meaning Remedy Blank MDInternal care MaintenanceSpecifications External careMemo Calling for Service Limited WarrantySharp Plaza, Mahwah, New Jersey