Heat Controller HEV/H manual General Information

Page 5

Heat Controller, Inc.

HEV/H SERIES

Installation, Operation & Maintenance

 

 

 

GENERAL INFORMATION

Inspection

Upon receipt of the equipment, carefully check the shipment against the bill of lading. Make sure all units have been received. Inspect the packaging of each unit, and inspect each unit for damage. Insure that the carrier makes proper notation of any shortages or damage on all copies of the freight bill and completes a common carrier inspection report. Concealed damage not discovered during unloading must be reported to the carrier within 15 days of receipt of shipment. If not filed within 15 days, the freight company can deny the claim without recourse. Note: It is the responsibility of the purchaser to file all necessary claims with the carrier. Notify Heat Controller of all damage within fifteen (15) days of shipment.

Storage

Equipment should be stored in its original packaging in a clean, dry area. Store units in an upright position at all times. Stack units a maximum of 3 units high.

Unit Protection

Cover units on the job site with either the original packaging or an equivalent protective covering. Cap the open ends

of pipes stored on the job site. In areas where painting, plastering, and/or spraying has not been completed, all due precautions must be taken to avoid physical damage to the units and contamination by foreign material. Physical damage and contamination may prevent proper start-up and may result in costly equipment clean-up.

Examine all pipes, fittings, and valves before installing any of the system components. Remove any dirt or debris found in or on these components.

Pre-Installation

IInstallation,Operation,andMaintenanceinstructions areinstructionsprovided arewithprovidedeach unitwith. Horizontaleach unitequipment. Verticalisunit designedconfigurationsfor installationare typicallyaboveinstalledfalse ceilinga mechanicalor in ceiling plenumroom. The. Otherinstallationunit c figurationssite chosenareshouldtypicallyincludeinstalled inadequatemechanical room. The installation site chosen

ervice clearance around the unit. Before should include adequate service clearance around the unit start-up, read all manuals and become familiar

unit. Before unit start-up, read all manuals and become with the unit and its operation. Thoroughly check the familiar with the unit and its operation. Thoroughly check system before operation.

the system before operation.

Prepare units for installation as follows:

1.Compare the electrical data on the unit nameplate with ordering and shipping information to verify that the correct unit has been shipped.

2.Keep the cabinet covered with the original packaging until installation is complete and all plastering, painting, etc. is finished.

3.Verify refrigerant tubing is free of kinks or dents and that it does not touch other unit components.

4.Inspect all electrical connections. Connections must be clean and tight at the terminals.

5.Remove any blower support packaging.

6.Loosen compressor bolts on units equipped with compressor spring vibration isolation until the compressor rides freely on the springs. Remove shipping restraints.

7.REMOVE COMPRESSOR SUPPORT PLATE 1/4” Some airflow patterns are field convertible (horizontal

SHIPPING BOLTS (2 on each side) TO MAXIMIZE units only). Locate the airflow conversion section of

VIBRATION AND SOUND ATTENUATION. this IOM.

8.Some airflow patterns are field convertible (horizontal Locate and verify any hangers, or other accessory

units only). Locate the airflow conversion section of kits located in the compressor section or blower

this IOM. section.

9.Locate and verify any hangers, or other accessory kits located in the compressor section or blower section.

ѥ CAUTION! ѥ

CAUTION! DO NOT store or install units in corrosiveѥenvironmentsCAUTION!or in locationsѥ

subject to temperature or humidity extremes CAUTION! DO NOT store or install units (e.g., attics, garages, rooftops, etc.).

in corrosive environments or in locations Corrosive conditions and high temperature subject to temperature or humidity extremes or humidity can significantly reduce

(e.g., attics, garages, rooftops, etc.). performance, reliability, and service life. Corrosive conditions and high temperature Always move units in an upright position. or humidity can significantly reduce Tilting units on their sides may cause performance, reliability, and service life. equipment damage.

Always move units in an upright position.

Tilting units on their sides may cause

equipment damage.

NOTICE! Failure to remove shipping brackets from spring-mounted compressors will cause

excessive noise, and could cause component NOTICE! Failure to remove shipping brackets failure due to added vibration.

from spring-mounted compressors will cause excessive noise, and could cause component

failure due to added vibration.

ѥ CAUTION! ѥ

CAUTION! CUT HAZARD - Failure to follow this cautionѥmayCAUTION!result in personalѥinjury.

Sheet metal parts may have sharp edges CAUTION! CUT HAZARD - Failure to follow or burrs. Use care and wear appropriate this caution may result in personal injury. protective clothing, safety glasses and Sheet metal parts may have sharp edges gloves when handling parts and servicing

or burrs. Use care and wear appropriate heat pumps.

protective clothing, safety glasses and

gloves when handling parts and servicing heat pumps.

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Residential Packaged Geothermal Heat Pump Table of Contents Unit Nomenclature Configuration Supply AIR OptionsSafety General Information Vertical Upflow Physical DataHE Vertical Upflow Dimensional Data Return Connection Standard Deluxe Filter Frame Vertical Unit Location Vertical InstallationCondensate Piping for Vertical Units Sound Attenuation for Vertical UnitsMounting Horizontal Units Vertical InstallationHorizontal Unit Location Typical Closed Loop Horizontal Unit Installation Horizontal InstallationSide to Back Discharge Conversion Field Conversion of AIR DischargeField Conversion of Air Discharge GROUND-LOOP Heat Pump Applications Water Connection InstallationAntifreeze Low Water Temperature Cutout Setting DXM2 ControlWater Quality Standards GROUND-WATER Heat Pump ApplicationsOpen Loop Ground Water Systems Expansion Tank and Pump Water Coil Low Temperature Limit SettingWater Control Valve Flow RegulationWater Quality Standards Water Quality StandardsHOT Water Generator Typical HWG InstallationInstallation HWG Water Piping Water Tank PreparationWater Tank Refill Initial Start-UpElectrical Line Voltage General Line Voltage WiringElectrical Line Voltage Power Connection Electrical Power WiringHWG Wiring Volt OperationThermostat Connections Electrical LOW Voltage WiringLow Water Temperature Cutout Selection Thermostat Accessory ConnectionsTaco Valve Thermostat Installation Electrical Thermostat WiringECM Blower Control ECM Blower Performance Data Table Blower Performance DataWiring Diagram Unit Operation DXM2 ControlsP11 DXM2 Layout and ConnectionsCommissioning Conditions Unit Commissioning and Operating ConditionsOperating Limits Unit Starting and Operating Conditions Unit and System Checkout Unit Start-up ProcedureUnit START-UP and Operating Conditions Unit START-UP Procedure Unit START-UP ProcedureHE Coax Water Pressure Drop Unit Operating ConditionsHE Series Typical Unit Operating Pressures and Temperatures Unit Operating Conditions Preventive Maintenance Troubleshooting Start DXM2 Process Flow ChartFault Htg Clg Possible Cause Solution Functional TroubleshootingIFC Fault Code 410A Troubleshooting FormHEV/H Series 97B0016N11

HEV/H specifications

The Heat Controller HEV/H series represents a significant advancement in heating technology, designed to provide efficient and effective climate control for both residential and commercial spaces. This innovative range of heat pumps combines cutting-edge features with user-friendly functionality to offer a reliable solution for modern heating needs.

One of the standout features of the HEV/H series is its advanced inverter technology. This system allows the heat pump to adjust its output based on the specific heating requirements of the environment. By varying the compressor's speed, the HEV/H maintains a consistent temperature while significantly reducing energy consumption. This not only lowers utility bills but also reduces environmental impact, making it a more sustainable option compared to traditional heating methods.

The HEV/H series is equipped with a high-efficiency heat exchanger, which maximizes heat transfer and enhances overall performance. This component ensures that the system can operate effectively even in colder climates, providing reliable heating throughout the winter months. Additionally, the unit’s low noise operation is designed to maintain a peaceful environment, making it suitable for bedrooms, offices, and other noise-sensitive areas.

Another notable characteristic of the HEV/H series is its smart control features. Integrated with Wi-Fi connectivity, users can conveniently manage their heating settings remotely via a smartphone app. This feature allows for customized scheduling and temperature control, ensuring optimal comfort and convenience. Users can also receive real-time notifications on energy consumption and system performance, enhancing user engagement and control.

The HEV/H series also emphasizes durability and longevity. Constructed with high-quality materials, the units are designed to withstand the rigors of daily use while requiring minimal maintenance. The incorporation of advanced filtration systems helps to improve indoor air quality by capturing dust and allergens, which is especially beneficial for individuals with allergies or respiratory issues.

In summary, the Heat Controller HEV/H series exemplifies modern heating technology with its combination of efficiency, control, and user-friendly features. Its inverter technology, high-efficiency heat exchangers, smart connectivity, and durable construction make it an outstanding choice for anyone seeking to enhance their indoor climate while being conscious of energy usage and environmental impact. Whether for a home or business, the HEV/H series is poised to deliver exceptional heating solutions tailored to diverse needs.
Top Page Image Contents