Heat Controller HMG**F1E, HMG**X1E Horizontal Installations, Horizontal Left Installations

Page 7

Horizontal Installations

These air handlers can be installed horizontally in an attic, basement, crawl space or alcove.It can also be suspended from a ceiling in a basement or utility room in either a right to left airflow or left to right airflow as shown in Figure 3. Air handlers may or may not be shipped from the factory with all the parts required for horizontal left applications and horizontal right applications.If your unit does not have parts for a horizontal application, a kit may be available.

NOTE: In all horizontal applications in which the unit is installed above a finished ceiling and/or living space, a secondary drain pan must be installed under the entire unit to avoid damage to the ceiling in the event of condensate overflow.Additionally, it is recommended that an approved water level indicator or float switch device be used to shut down the unit in the event water is detected in the auxiliary drain pan.

If suspending the air handler from the ceiling, assemble a support frame (Figure 4) using slotted iron channel and full threaded rod. Fasten the frame together with nuts, washers, and lockwashers. Secure the support frame to the rafters with lag bolts. The air handler can also be

HORIZONTAL RIGHT

RETURN

AIR

HORIZONTAL LEFT

RETURN

AIR

Figure 3. Horizontal Configurations

 

Nuts (x2)

 

Lag

 

Bolt

Threaded

Washer

and

Rod

Lockwasher

 

 

Nuts (x2)

Figure 4. Unit Horizontally Suspended

suspended using steel straps around each end of the unit.The straps should be attached to the air handler with sheet metal screws and to the rafters with bolts.

Horizontal Left Installations:

1.Remove the coil access door.

2.Remove the plug from one of the threaded holes in the horizontal drain pan. Completely remove the webbing located in the threaded holes of the horizontal drain pan. IMPORTANT: If the webbing is not removed, the condensate will not drain properly and ceiling damage may occur.

3.Insert the plug (from horizontal drain pan) into the open and unused drain hole in the drain pan at the bottom of the unit to block bypass air.

4.Remove the corresponding drain line knockout from the coil access door to allow access to the horizontal drain.

5.Replace the door and attach the drain line.

Horizontal Right Installations:

1.Remove the coil access door. Unscrew the line-set tube close-off plate from the front left cabinet rail.

2.Slide the coil and drain pan assembly out of the unit.

3.Remove the sheet metal hairpin covers (if supplied) from the back of the coil and discard.

4.Place the horizontal drain pan on the opposite side of the coil. On units with 2 sets of knockouts, remove the other set of knockouts in the coil spacing plates and insert support rod.

5.Slide the coil and the horizontal drain pan assembly back into the unit. Re-attach the tube close off plate.

NOTE: For 24K & 30K BTUH applications, it may be preferrable to remove the blower assembly prior to installing the coil & drainpan. In this case follow instructions 1-4 as listed above but also remove the blower access door and blower assembly. The blower assembly is secured with two screws on either side near the front.With these removed the blower assembly can slide out of the front of the unit. Install the coil and drain pan as described in step 5 and then replace the blower assembly. Take care to ensure that the flanges on the sides of the blower assembly are captured by the pockets in the blower deck. It may be necessary to lift the blower assembly during insertion to allow the lower blower leg to clear the side of the drain pan. The blower will stop against the back of the blower deck. Replace the two screws and the blower access door and procede with steps 6-9.

6.Remove the plug from one of the threaded holes in the horizontal drain pan. Completely remove the webbing located in the threaded holes of the drain pan.

IMPORTANT: If the webbing is not removed, the condensate will not drain properly and ceiling damage may occur.

NOTE: It is recommended that the suction line be insulated up to the coil inside of the cabinet.

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents AIR Handler Table of Contents Health Flammability Reactivity Important Safety InformationNitrogen Requirements & CodesMinimum Clearances Before You Install this UnitGeneral Information Locating the Air HandlerAir Filters Installation in a GaragePlenums & Air Ducts Unconditioned SpacesMounting Applications Air handler InstallationDownflow Installations Packaging RemovalHorizontal Left Installations Horizontal InstallationsHorizontal Right Installations Nitrogen Refrigerant Line ConnectionsConnecting the Linesets Orifice Removal & InstallationCondensate Drainage Example Electrical connections Pre-Electrical ChecklistThermostat Connections Twinning Control BoardHumidifier Startup & AdjustmentsElectronic Air Cleaner EAC Heater KitsRefrigerant Charging Blower ConfigurationsAir Circulation Selecting Basic Heating Airflow Dehumidification OptionsSelecting Basic Cooling / Heat Pump Airflow Troubleshooting Unit MaintenanceFurnace Size Btuh Detail D Figures & TablesBreaker 60A Heating Element Dry Coil ESP Airflow DataAirflow Data for HMG**F1E Series Air Handlers Airflow Data for HMG**X1E Air Handlers TON HCG36V1E & HCG42V1E HCG24V1E & HCG30V1ECFM TONHCG48V1E HCG60V1E Airflow Data for HCG**V1E Air HandlersHCG24V1E HCG30V1E HCG36V1E HCG42V1ESingle Stage Control Board Electrical diagrams & DataFixed Speed Motor Control Board Handler Wiring Diagram for HMG**F1E Series AirSeries Air Handler Air Handler with Fixed Speed High Efficiency MotorHCG**V1E Series Air Handler Wiring Diagram forMCA MOP HMG**F1E SeriesH6HK Models Number Control Signal & Mode Operation Total KW Board ActionControl Board Operation Air Handler ModelAUX Heat FAN Installation Address Installer Name

HMG**X1E, HCG**V1E, HMG**F1E specifications

The Heat Controller series, comprising models HMG**F1E, HCG**V1E, and HMG**X1E, showcases advanced heating and cooling technologies designed for optimal comfort and energy efficiency in residential and commercial settings. Each model is equipped with a range of features that cater to diverse user needs while maintaining excellent performance.

The HMG**F1E model stands out with its sleek design and compact size, making it ideal for smaller spaces. It utilizes inverter technology, which enables the unit to operate at variable speeds for greater efficiency and reduced energy consumption. This model also comes with a user-friendly remote control, allowing for easy adjustments of temperature settings and operational modes without the need to manually interact with the unit itself. The HMG**F1E is equipped with a filtration system that improves indoor air quality by removing dust and allergens, providing a more comfortable living environment.

In contrast, the HCG**V1E model is designed with versatility in mind, offering both heating and cooling functions. This unit features a programmable thermostat, allowing users to set their preferred temperatures for different times of the day. The HCG**V1E is manufactured with durable materials that ensure longevity and reliability under various weather conditions. Additionally, it provides whisper-quiet operation, ensuring minimal disturbance to indoor activities. The energy-efficient operation and smart climate control technology contribute to significant savings on energy bills.

Finally, the HMG**X1E model is known for its cutting-edge smart technology integration. This model can be connected to smart home systems, enabling users to control the unit from their smartphones or tablets. It features advanced sensors that detect occupancy and adjust heating and cooling accordingly, optimizing energy usage in real-time. The HMG**X1E also incorporates an eco-friendly refrigerant, aligning with modern environmental standards while delivering exceptional performance.

Overall, the Heat Controller series with models HMG**F1E, HCG**V1E, and HMG**X1E redefine comfort and efficiency. With their combination of innovative technologies, user-friendly features, and sustainable designs, they are perfect for anyone seeking reliable temperature control solutions for their spaces.
Top Page Image Contents