Haier KC18AGH, SAP-K18AM instruction manual Basic Requirements for Installation Position

Page 23

Installation Service

7. NOTICES FOR INSTALLATION

Important Notices

1.

The unit installation work must be done by qualified

 

personnel according to the local rules and this manual.

 

 

 

 

 

2.

Before install, please contact with local authorized

 

 

maintenance center. If the unit is not installed by the

 

 

authorized maintenance center, the malfunction may

 

 

not solved, due to discommodious contacts.

 

3.

When removing the unit to the other place, please

 

 

firstly contact with the authorized SANYO Maintenance

 

 

Center in the local area.

7.1Basic Requirements for Installation Position

Install in the following place may cause malfunction. If it is unavoidable contact with service center please:

1.Place where strong heat sources, vapors, flammable gas or volatile object are emitted.

2.Place where high-frequency waves are generated by radio equipment, welders and medical equipment.

3.Place where a lot of salinities such as coast exists.

4.Place where a sulfured gas such as the hot spring zones is generate.

5.Place where the oil (machine oil) is contained in the air.

6.Other place with special circumstance.

7.2Indoor Unit Installation Position Selection

1.The air inlet and outlet vent should be far from the obstruction, make sure that the air can be blown through the whole room.

2.Select a position where the condensing water can be easily drained out, and the places easily connected for outdoor unit.

3.Select a location where the children can not reach.

4.Can select the place where is strong enough to withstand the full weight and vibration of the unit. And will not increase the noise.

5.Be sure to leave enough space to allow access for routine maintenance. The height of installed location should be

200cm or more from the floor.6. Select a place about 1m or more away from TVset or any other electric appliances.

7.Select a place where the filter can be easily taken out.

8.Make sure that the indoor unit installation should accord with installation dimension diagram requirements. (Pg.24)

7.3Outdoor Unit Installation Position Selection

1.Select a location from which noise and outflow air emitted by unit will not inconvenience neighbours, animals, plants.

2.Select a location with sufficient ventilation.

3.Select a location where there should be no obstructions cover the inlet and outlet vent.

4.The location should be able to withstand the full weight and vibration of the outdoor unit and permit safe installation.

5.Select a dry place, but do not expose under the direct sunlight or strong wind.

21

Page 22 Page 24
Image 23
Page 22 Page 24
Contents 85S-6-4181-002-00-0 Split System Air Conditioner Contents Operation and Maintenance Operation and Maintenance Heat Pump Model Only Conditions of Unit Cant Operate Normally Working Temperature RangeIndoor Unit Names and Fuctions of Each PartRemote Control Unit Display Operation of Wireless Remote Control UnitRemote Control Unit Functions How it Works? AutoStep Using the General OperationTimer OFF mode Example Using the 24-Hour on or OFF TimerSetting procedure Heating Mode Using the Sleep OperationCooling and DRY Mode Sleep Mode is used for saving energy Auto Operation How it works? Blow Operation Using of the Special Features & RemarksSetting OFF the displayer indicator light DRY Operation How it works?Swing Operation How it works? Emergency Operation Fig How to Install BatteriesUsing the Remote Control Unit Fig Washing Clean and CareClean the Front Panel Take off the front panelMaintain After Use Cleaning the Air FiltersCleaning Check Before You UsePhenomenon TroubleshootingPhenomenon Troubleshooting Troubleshooting Outdoor Unit Installation Position Selection Basic Requirements for Installation PositionIndoor Unit Installation Position Selection Wrong connection, may cause fire Safety Requirements for Electric AppliancesEarthing Requirements Others Space to the obstruction Installation Diension DiagramSpace to the ceiling Space to the wallInstall the Water Drainage Pipe Install Indoor UnitInstall the Real Panel Install the Piping HoleWiring Instructions Connect Indoor and Outdoor Electric WireWiring System Diagram Wire Length and DiameterHow to Install the Indoor Unit Wiring Instructions for the Outdoor Unit Install Outdoor UnitDeburring Flaring Procedure With a Flare ToolRefrigerant Tubing Use of The Flaring MethodTaping the Tubes Connecting Tubing between Indoor and Outdoor UnitsFinish the Installation Insulation of Refrigerant TubingAIR Purging with a Vacuum Pump for Test RUN Air PurgingAir Purging Tubing Length AccessoriesHow to install Pump Down What is Pump Down?Pump Down Procedure Test Operation Check After Installation and Test RUNCheck After Installation

KC18AGH, SAP-K18AM specifications

The Haier SAP-K18AM and KC18AGH are part of Haier's innovative line of air conditioning solutions designed to provide efficient cooling and exceptional comfort in various environments. These models stand out for their blend of modern technology, user-friendly features, and energy efficiency.

One of the main features of the Haier SAP-K18AM is its powerful cooling capacity, which enables it to quickly lower indoor temperatures, making it ideal for larger spaces or warmer climates. With a cooling capacity of 18000 BTU, this model ensures that even during the hottest summer days, users can enjoy a refreshing indoor atmosphere. The unit operates quietly, allowing for peaceful relaxation or focused work without the disturbance of loud compressor noises.

The KC18AGH model is equipped with advanced inverter technology that adjusts the compressor speed according to the cooling demand. This feature not only enhances energy efficiency but also helps to maintain a consistent temperature throughout the space. The inverter technology significantly reduces electricity consumption compared to non-inverter models, making it an environmentally friendly choice.

Both models come with a range of convenient features, including multiple cooling and fan speed options, sleep mode, and a programmable timer. The sleep mode function gradually increases the temperature at night, ensuring a comfortable sleep environment while saving energy. The programmable timer allows users to set the air conditioning unit to operate only when needed, further optimizing energy use.

Additionally, the Haier SAP-K18AM and KC18AGH are designed with user comfort in mind. They come with an easy-to-use remote control, allowing for effortless adjustments from across the room. The units also include a self-cleaning feature that helps reduce mold and bacteria buildup, ensuring that the air quality remains high.

In conclusion, the Haier SAP-K18AM and KC18AGH air conditioners represent cutting-edge technology and design. With powerful cooling capabilities, energy-efficient inverter technology, and a suite of user-friendly features, these models are ideal for anyone looking to improve the comfort and quality of their indoor environment. Whether for residential or commercial use, Haier continues to set the standard in reliable and effective air conditioning solutions.
Top Page Image Contents