tango_studio_manual.qxd 2/13/08 4:56 PM Page 9
Unpacking and Initial Setup
1.Remove Tango Studio from the box and remove foam and protective plastic. Keep original packaging for 90 days and then properly dispose.
2.Place Tango Studio on a level surface following the precautions listed in the safety warnings.
3.Remove AC adapter from the packaging.
4.Read and review manual and safety warnings
5.Connect the AC adapter into the jack on the back of Tango Studio labeled “12V DC ”, then plug the AC adapter into the wall outlet.
6.Untie and extend the FM antenna on the back of the unit so that it is not tangled.
2 | 3 | 4 | 5 |
| 1. | Retractable Universal |
| 6 | Dock Well |
1 | 2. | Power On/Off |
| 3. | Select Source |
| 4. | Previous/Next Track |
|
| (iPod) |
| 6 | Tune Up/Down Frequency |
|
| (Radio) |
| 5. | Volume Up/Down |
16. LED Display
|
|
|
|
|
|
|
|
|
|
| 1. | 12V DC Power Jack |
|
|
|
|
|
|
|
|
|
|
| 2. | |
|
|
|
|
|
|
|
|
| 3 |
| 3. | FM Antenna |
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
| 1 | 2 |
|
|
|
| ||||
1 |
| 2 |
|
| 1. | Power Button | 5. Volume Down | |||||
| 3 |
| ||||||||||
7 |
|
| 4 2. | Volume Up | 6. | Select Source | ||||||
|
|
|
| |||||||||
|
|
| Play (iPod) | 7. | Previous Track (iPod) | |||||||
5 |
|
|
|
| 3. | |||||||
|
|
|
| 4. | Next Track (iPod) |
| Down Tuning (Radio) | |||||
|
|
|
|
|
|
| ||||||
Up Tuning (Radio)
6
Listening to your iPod
1.Press the XtremeMac logo at the bottom of front of the unit to open the universal dock well.
2.Take the insert that came with your iPod and gently press the insert into the universal dock well.
3.Carefully place your iPod into the dock.
4.Press the power button on top of the unit and the display will light “iPod” to indicate the unit is powered and an iPod is properly docked. The display will go off after 10 seconds.
5.Press play on the iPod or on the included remote.
6.Use the volume controls on the top of the unit or on the included remote to set to the desired volume level. Use the iPod to control songs or use the remote for next/previous track.
Note: If “iPod” is not shown on the display, use the source button to select iPod mode and press play on the iPod or remote.
Listening to the FM radio
1.Press the source button to select radio mode. The display will show the station that was last used. The display will go off after 10 seconds.
2.Use the tuning controls on the top of the unit or on the included remote to tune to the desired frequency. Holding down the tuning controls will scroll quickly through stations.
3.Use the volume controls on the top of the unit or on the included remote to set to desired volume level.
Note: To ensure quality radio reception, Tango Studio will not charge a docked iPod while FM radio is selected as the source.
Listening to an Auxiliary Source
1.Connect the device to the
2.Press the source button on the top of the unit so that the display shows “AUX”. The display will go off after 10 seconds.
3.Press play on the device.
4.Use the volume controls on the top of the unit or on the included remote to set to desired volume level.
5 Tango Studio User’s Guide | Tango Studio User’s Guide 6 |