Bowers & Wilkins CCM817 owner manual English, Limited Warranty

Page 5

English

Limited Warranty

Dear customer,

Welcome to B&W.

This product has been designed and manufactured to the highest quality standards. However, if something does go wrong with this product, B&W Loudspeakers and its national distributors warrant free of charge labour (exclusion may apply) and replacement parts in any country served by an official B&W distributor.

This limited warranty is valid for a period of five years from the date of purchase or two years for electronics including amplified loudspeakers.

Terms and Conditions

1The warranty is limited to the repair of the equipment. Neither transportation, nor any other costs, nor any risk for removal, transportation and installation of products is covered by this warranty.

2This warranty is only valid for the original owner. It is not transferable.

3This warranty will not be applicable in cases other than defects in materials and/or workmanship at the time of purchase and will not be applicable:

a.for damages caused by incorrect installation, connection or packing,

b.for damages caused by any use other than correct use described in the user manual, negligence, modifications, or use of parts that are not made or authorised by B&W,

c.for damages caused by faulty or unsuitable ancillary equipment,

d.for damages caused by accidents, lightning, water, fire heat, war, public disturbances or any other cause beyond the reasonable control of B&W and its appointed distributors,

e.for products whose serial number has been altered, deleted, removed or made illegible,

f.if repairs or modifications have been executed by an unauthorised person.

4This guarantee complements any national/regional law obligations of dealers or national distributors and does not affect your statutory rights as a customer.

How to claim repairs under warranty

Should service be required, please follow the following procedure:

1If the equipment is being used in the country of purchase, you should contact the B&W authorised dealer from whom the equipment was purchased.

2If the equipment is being used outside the country of purchase, you should contact B&W national distributor in the

country of residence who will advise where the equipment can be serviced. You can call B&W in the UK or visit our web site to get the contact details of your local distributor.

To validate your warranty, you will need to produce this warranty booklet completed and stamped by your dealer on the date of purchase. Alternatively, you will need the original sales invoice or other proof of ownership and date of purchase.

Owner’s manual

Introduction

Thank you for purchasing Bowers and Wilkins CCM817 speakers.

Since its foundation in 1966, the continuing philosophy of B&W has been the quest for perfect sound reproduction. Inspired by the company’s founder, the late John Bowers, this quest has entailed not only high investment in audio technology and innovation but also an abiding appreciation of music and movies to ensure that the technology is put to maximum effect.

The CCM817 is an audiophile quality speaker, primarily designed for in-ceiling mounting in 2-channel and home theatre installations. Its angled baffle enables the optimum listening axis to be directed more towards the listening area, which improves sound quality and imaging in a way that normal ceiling speakers cannot offer. It also has applications as an in-wall surround speaker.

However, no matter how good the speakers themselves, they will not deliver their full potential unless properly installed. Please read through this manual fully. It will help you optimise the performance of the system.

B&W distributes to over 60 countries worldwide and maintains a network of dedicated distributors who will be able to help should you have any problems your dealer cannot resolve.

Check the contents

This pack should contain:

2x Baffle with drive units and crossover

2x Grille

2x Paint mask

2x Alignment template

Choosing the position

Check that there is no conflict with other installations (pipe work, air conditioning, power cabling etc.). In existing drywall construction, use a stud-finding tool to map the construction accurately and a pipe detector to scan the proposed installation position.

Refer to the section drawing of the speaker and ensure that there is enough clearance behind the plasterboard (sheetrock) for the clamps to swing out fully.

Avoid installing the speakers in the same cavity as flimsy ducting, which may be induced to rattle.

The speakers are designed to operate satisfactorily in a wide range of cavity volumes, ideally above 15 litres (0.5 cu ft), so make sure the volume is not too restricted by cross studs.

In solid wall construction, be prepared to provide a cavity in the wall that extends outside the boundaries of the speaker's frame, otherwise bass performance will be compromised.

The speakers are balanced for half-space mounting (ie flush in a ceiling or soffit). Placement near a wall/ceiling junction or in a corner may give rise to too much bass and a boomy quality to the sound. Try to keep the speakers at least 0.5m (20in) from wall/ceiling edges.

The following sections give guidance on optimum positioning, but this may be modified in line with domestic constraints.

WARNING: The speakers produce a static magnetic field. As such They should not be placed within 0.5m (20in) of equipment that may be affected by such a field (eg Cathode Ray Tubes in TVs and Personal Computers).

Front speakers for audio or home theatre

The CCM 817 is ideal for use when it is required that the speakers be mounted in the ceiling so as to be as unobtrusive as possible. For home theatre, they should be mounted about 0.5m (20 in) from the plane of the screen or the front wall in the case of an audio-only installation. The frame should be rotated so that the drive units are directed towards the listening area.

(figure 1)

For 2-channel applications, the speakers should subtend an angle of between 40º and 60º at the centre of the listening area. (figure 2)

For home theatre, the left and right speakers should be approximately 0.5m (20 in) from the sides of the screen. (figure 3)

Surround speakers

The speakers should normally be positioned in the ceiling with the frame rotated so that the drive units are directed towards the centre of the listening area.

5.1 channel

The horizontal angle to the centre of the listening position should be approximately 120º round from the centre of the screen.

The speakers may also be successfully mounted in the side wall for this application. They should be positioned at least 60cm (2 ft) above ear height and with the frames rotated so that the drive units are directed towards the centre of the listening area. (figure 4)

6.1 channel

Position two speakers to the sides in line with the centre of the listening area and one centrally behind the listeners, with the frames rotated so that the drive units are directed towards the centre of the listening area. (figure 5)

2

Image 5
Contents Custom Installation Series Page Page Contents English Limited WarrantyPreparing the Location Manuel d’utilisation FrançaisGarantie limitée Préparation DE ’INSTALLATION Bedienungsanleitung DeutschGarantie Vorbereitungen FÜR DEN Einbau Manual de instrucciones EspañolGarantía limitada Preparando LA Colocación Manual do utilizador PortuguêsGarantia limitada Preparando a Localização Manuale di istruzioni ItalianoGaranzia limitata Preparazione DELL’INSTALLAZIONE Handleiding NederlandsBeperkte garantie Voorbereiding Περι Εγγύηση ΕλληνικάΚαι πρ Πως µπνα Επισκευές υπτην παρ εγγύησηΠρτυ Υ Εγκαταστασησ Κανκατασκευή συµπαγής Ρύθµιση τηΜτης κ ΤτηРуководство по эксплуатации РусскийОграниченная Гарантия Подготовка К Монтажу Návod k pouãití EskyZáruka Píprava Umístní Használati útmutató MagyarKorlátozott garancia Hely EL¥KÉSZÍTÉSE Instrukcja uÃytkownika PolskiGwarancja Przygotowanie Miejsca MONTA…U Indywidualne dostosowanie Ustawienie g¡o·nikaPage Page Page CCM817 Ll09805 Issue