Turbosound TA-500DP, TA-500TDP, TA-500HDP, TA-500HM Secondary Safeties, Safety Inspections

Page 19

user manual

TA-500

Secondary Safeties

All loudspeakers flown in theatres, studios or other places of work and entertainment must, in addition to the principle load bearing means of suspension, be provided with an independent, properly rated and securely attached secondary safety.

Only steel wire ropes or steel chains of an approved construction and load rating may be used as secondary safeties. Plastic covered steel wire ropes are not permitted for use as secondary safeties.

Safety Inspections

Carefully inspect rigging systems components and cabinets for defects or signs of damage before proceeding to assemble a flown array. If any parts are damaged or suspect, DO NOT USE THEM.

Regular, more rigorous test and inspection of rigging components must also be carried out. Safety legislation and test and inspection requirements will vary from country to country. In most cases, annual independent test and inspection by a suitably approved and qualified inspector will be required. Users must ensure compliance with all applicable safety requirements.

Turbosound recommends regular safety inspections and further recommends that a logbook be kept detailing the test and inspection history of each Turbosound rigging accessory.

Turbosound has adopted the following load safety factors:

•12 x load safety factor: Chains, ropes, shackles, eyebolts, straps and hooks.

•5 x load safety factor: Accessories generally employed in fixed, permanent installations.

Always wear protective headwear, footwear and eye protection in accordance with local regulations. Anyone involved in flying ANY sound system, especially in a touring capacity, should take note of the following advice:

The rigging of a flown sound system may be dangerous unless undertaken by qualified personnel with the required experience and certification to perform the necessary tasks. Fixing of hanging points in a roof should always be carried out by a professional rigger and in accordance with the local rules of the venue. The house rigger and/or building manager must always be consulted.

You should observe particularly the following points:

TA-500 user manual

Page 19

Image 19

Contents Aspect TA-500 Systems TA-500 TA-500 TA-500 Audio Connections & Controls TA-500HDP EC Declaration of ConformityTurbosound Aspect System Concepts IntroductionAspect Polyhorn Concept TA-880 TA-500 Narrow 25º horizontal coverage LMS-D2X Loudspeaker Management Systems Loudspeaker Management System LMS ConceptNetwork Capability Aspect Loudspeaker Components Power AmplifiersSelf-powered Loudspeakers Digital ControllersTA-500 TA-500t Touring Three-way Loudspeaker TA-500DP Self-powered Three-way LoudspeakerTA-500tDP Self-powered Touring Three-way Loudspeaker TA-500 Three-way LoudspeakerTSW-218 Subwoofer TA-500HDP Self-powered Horizontal Three-way LoudspeakerTA-500H Horizontal Three-way Loudspeaker TA-500HM Two-way High/Mid LoudspeakerB18 Subwoofer B18DP Self-powered SubwooferTransportation Overview Flying and StackingSafety Notes on Rigging Secondary Safeties Safety InspectionsTA-500 Sample Certificate of Load Test Vertical Coverage Flying HardwareAspect TA-500 Flying Systems Horizontal CoverageTA-500T Touring Flying System Flybar SettingsTouring two-wide flybar TOP View FC-500T Flying Chains Flying MatrixTA-500 Integral Flying Hardware TS-890 Tilting StrapsCaptive Biscuit BoltLocking Mechanism Connecting Flying Chains to the CabinetSliding the top chain profile into the slot Assembly of the Top Chains to the CabinetAdding additional rows Connection of additional rowsAttaching the biscuit Setting the angles between rowsBiscuit slides into lower cabinet Attaching the Tilt StrapsFront view of the assembled cluster Lifting the columnTA-500 TA-500 Install Flying System Rigging Instructions TA-500 TA-500 Array is now ready to pick up Flying a single TA-500 cabinet using M10 eyebolts Unpacking Mechanical InstallationLMS Series Loudspeaker Management Systems IntroductionLMS-D24 and D26 Loudspeaker Management Systems FeaturesLCD Front Panel FunctionsTA-500 Rear Panel Functions Operating the LMS-D24 and D26 Starting up Selecting a Factory PresetCreating a Crossover Navigation and Viewing Parameters EQ1 100Hz 0dBNavigation Out1 Freq Width Gain EQ1 100Hz 1.4Q 0.0dBPreset Recall PresetsStore My System Preset StoreOutput DSP block diagram DSP Processing Layout Input DSP block diagramStereo / Mono Formats DSP processing Input Channels A Delay 1.50msA Freq Shape High and Low shelving filters Parametric EqualisationParametric filters Output Channels Gain and Polarity DelayHigh and Low Pass Filters Out1 Freq Shape LPF 2.50k LR24Out1 Freq Slope Gain EQ- 100Hz 12dB 0.0dB Routing LimitersUtilities Utility functions General Features & Facilities T-45 High Efficiency Audio Power AmplifiersFront Panel Functions T-25 Front Panel Functions T-45 Powering Up Mains PowerSafety Earthing Voltage Range Voltage SettingAudio Connections & Controls Polarity Gain and Sensitivity SettingsInput Impedance Output Connections Attenuation & Gain SettingDamping Factor Cooling System Long Speaker LinesTA-500 TA-500t TA-500H TA-500HM Appendix a Technical SpecificationsTA-500DP TA-500tDP TA-500HDP Stock Code Model Description Appendix B Spare Parts ListAppendix C Warranty TA-500

Related manuals

Manual 73 pages 47.45 Kb