Turbosound TA-500TDP, TA-500HDP, TA-500DP, TA-500HM user manual Safety Notes on Rigging

Page 18

user manual

TA-500

Safety Notes on Rigging

The Turbosound Aspect rigging system has been designed and constructed to a high standard of safety, and tested to the most demanding of specifications. In order to ensure the highest safety standards, the information following on

the assembly and safe use of rigging accessories must be carefully understood and followed.

Only use Turbosound recommended rigging accessories, which are specifically designed for their intended purpose. Do not use Turbosound rigging with other types or brands of loudspeakers. This practice may compromise safety standards and Turbosound will not be responsible for damage or injury so caused.

Do not modify the rigging accessories, or use them in a way other than that described in this user manual. Rigging components supplied as part of a complete assembly are non- interchangeable and must not be exchanged with the component parts of any other assembly.

The component parts of a Turbosound rigging accessory must only be assembled using the fasteners and methods of assembly recommended in this manual. The use of fasteners and methods of assembly not specified or approved by Turbosound may result in an unsafe rigging assembly. Welding, or any other means of permanently fixing rigging components to each other or to cabinet fixing points is not allowed.

Rigging assemblies must only be assembled using the appropriate parts and fixings as specified in this manual using the specific mounting instructions. Rigging components or assemblies must only be fixed to Turbosound loudspeaker cabinets using the cabinet fixing points, assembly methods and fasteners specified in this manual and the specific mounting instructions.

Walls, floors or ceilings must be capable of safely and securely supporting the actual load. The rigging accessory used must be safely and securely fixed both to the loudspeaker and to the wall, floor or ceiling.

When mounting rigging components on walls, floors or ceilings ensure that all fixings and fasteners used are of an appropriate size and load rating. Wall and ceiling claddings and the construction and composition of walls and ceilings all need to be taken into account when determining whether a particular fixing arrangement can be safely employed for a particular load. Cavity plugs or other specialist fixings, if required, must be of an appropriate type, fitted and used in accordance with the maker’s instructions.

Use only the rigging accessory fixing holes indicated in this manual and the specific mounting instructions to fix Turbosound rigging accessories to walls, floors or ceilings. Where specified, the recommended maximum torque settings for screw fasteners must be strictly complied with.

TA-500 user manual

Page 18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Aspect TA-500 Systems TA-500 TA-500 TA-500 Audio Connections & Controls EC Declaration of Conformity TA-500HDPIntroduction Turbosound Aspect System ConceptsAspect Polyhorn Concept TA-880 TA-500 Narrow 25º horizontal coverage Loudspeaker Management System LMS Concept LMS-D2X Loudspeaker Management SystemsNetwork Capability Digital Controllers Power AmplifiersSelf-powered Loudspeakers Aspect Loudspeaker ComponentsTA-500 TA-500 Three-way Loudspeaker TA-500DP Self-powered Three-way LoudspeakerTA-500tDP Self-powered Touring Three-way Loudspeaker TA-500t Touring Three-way LoudspeakerTA-500HM Two-way High/Mid Loudspeaker TA-500HDP Self-powered Horizontal Three-way LoudspeakerTA-500H Horizontal Three-way Loudspeaker TSW-218 SubwooferB18DP Self-powered Subwoofer B18 SubwooferTransportation Flying and Stacking OverviewSafety Notes on Rigging Safety Inspections Secondary SafetiesTA-500 Sample Certificate of Load Test Horizontal Coverage Flying HardwareAspect TA-500 Flying Systems Vertical CoverageFlybar Settings TA-500T Touring Flying SystemTouring two-wide flybar TOP View Flying Matrix FC-500T Flying ChainsTA-500 TS-890 Tilting Straps Integral Flying HardwareBolt Captive BiscuitConnecting Flying Chains to the Cabinet Locking MechanismAssembly of the Top Chains to the Cabinet Sliding the top chain profile into the slotConnection of additional rows Adding additional rowsSetting the angles between rows Attaching the biscuitAttaching the Tilt Straps Biscuit slides into lower cabinetLifting the column Front view of the assembled clusterTA-500 TA-500 Install Flying System Rigging Instructions TA-500 TA-500 Array is now ready to pick up Flying a single TA-500 cabinet using M10 eyebolts Introduction Mechanical InstallationLMS Series Loudspeaker Management Systems UnpackingFeatures LMS-D24 and D26 Loudspeaker Management SystemsFront Panel Functions LCDTA-500 Rear Panel Functions Selecting a Factory Preset Operating the LMS-D24 and D26 Starting upCreating a Crossover EQ1 100Hz 0dB Navigation and Viewing ParametersOut1 Freq Width Gain EQ1 100Hz 1.4Q 0.0dB NavigationPresets Preset RecallPreset Store Store My SystemDSP Processing Layout Input DSP block diagram Output DSP block diagramStereo / Mono Formats A Delay 1.50ms DSP processing Input ChannelsA Freq Shape Parametric Equalisation High and Low shelving filtersParametric filters Delay Output Channels Gain and PolarityOut1 Freq Shape LPF 2.50k LR24 High and Low Pass FiltersOut1 Freq Slope Gain EQ- 100Hz 12dB 0.0dB Limiters RoutingUtilities Utility functions T-45 High Efficiency Audio Power Amplifiers General Features & FacilitiesFront Panel Functions T-25 Front Panel Functions T-45 Mains Power Powering UpSafety Earthing Voltage Setting Voltage RangeAudio Connections & Controls Gain and Sensitivity Settings PolarityInput Impedance Attenuation & Gain Setting Output ConnectionsDamping Factor Long Speaker Lines Cooling SystemAppendix a Technical Specifications TA-500 TA-500t TA-500H TA-500HMTA-500DP TA-500tDP TA-500HDP Appendix B Spare Parts List Stock Code Model DescriptionAppendix C Warranty TA-500
Related manuals
Manual 73 pages 47.45 Kb
Top Page Image Contents