Turbosound TA-500TDP, TA-500HDP, TA-500DP, TA-500HM user manual

Page 38

user manual

TA-500

STEP 2 - Fit a 3-wide hinge brace to the top of the array and a 3-wide rear brace to the bottom of the array using the twelve M10 x 40mm hex screws provided and torque to 25Nm. The use of thread-locking compound is recommended (see Appendix). Fit an M10 eyebolt to the centre of the rear brace.

STEP 3 – Fit the enclosure connector to the top of the array.

Locate the four M10 eyebolts from the fixings kit supplied and insert these through the enclosure connector into the rigging points on the centre cabinet. These will be used to pick up the array.

TA-500 user manual

Page 38

Image 38

Contents Aspect TA-500 Systems TA-500 TA-500 TA-500 Audio Connections & Controls EC Declaration of Conformity TA-500HDPIntroduction Turbosound Aspect System ConceptsAspect Polyhorn Concept TA-880 TA-500 Narrow 25º horizontal coverage Network Capability Loudspeaker Management System LMS ConceptLMS-D2X Loudspeaker Management Systems Digital Controllers Power AmplifiersSelf-powered Loudspeakers Aspect Loudspeaker ComponentsTA-500 TA-500 Three-way Loudspeaker TA-500DP Self-powered Three-way LoudspeakerTA-500tDP Self-powered Touring Three-way Loudspeaker TA-500t Touring Three-way LoudspeakerTA-500HM Two-way High/Mid Loudspeaker TA-500HDP Self-powered Horizontal Three-way LoudspeakerTA-500H Horizontal Three-way Loudspeaker TSW-218 SubwooferB18DP Self-powered Subwoofer B18 SubwooferTransportation Flying and Stacking OverviewSafety Notes on Rigging Safety Inspections Secondary SafetiesTA-500 Sample Certificate of Load Test Horizontal Coverage Flying HardwareAspect TA-500 Flying Systems Vertical CoverageTouring two-wide flybar Flybar SettingsTA-500T Touring Flying System TOP View Flying Matrix FC-500T Flying ChainsTA-500 TS-890 Tilting Straps Integral Flying HardwareBolt Captive BiscuitConnecting Flying Chains to the Cabinet Locking MechanismAssembly of the Top Chains to the Cabinet Sliding the top chain profile into the slotConnection of additional rows Adding additional rowsSetting the angles between rows Attaching the biscuitAttaching the Tilt Straps Biscuit slides into lower cabinetLifting the column Front view of the assembled clusterTA-500 TA-500 Install Flying System Rigging Instructions TA-500 TA-500 Array is now ready to pick up Flying a single TA-500 cabinet using M10 eyebolts Introduction Mechanical InstallationLMS Series Loudspeaker Management Systems UnpackingFeatures LMS-D24 and D26 Loudspeaker Management SystemsFront Panel Functions LCDTA-500 Rear Panel Functions Creating a Crossover Selecting a Factory PresetOperating the LMS-D24 and D26 Starting up EQ1 100Hz 0dB Navigation and Viewing ParametersOut1 Freq Width Gain EQ1 100Hz 1.4Q 0.0dB NavigationPresets Preset RecallPreset Store Store My SystemStereo / Mono Formats DSP Processing Layout Input DSP block diagramOutput DSP block diagram A Delay 1.50ms DSP processing Input ChannelsA Freq Shape Parametric filters Parametric EqualisationHigh and Low shelving filters Delay Output Channels Gain and PolarityOut1 Freq Shape LPF 2.50k LR24 High and Low Pass FiltersOut1 Freq Slope Gain EQ- 100Hz 12dB 0.0dB Limiters RoutingUtilities Utility functions T-45 High Efficiency Audio Power Amplifiers General Features & FacilitiesFront Panel Functions T-25 Front Panel Functions T-45 Safety Earthing Mains PowerPowering Up Audio Connections & Controls Voltage SettingVoltage Range Input Impedance Gain and Sensitivity SettingsPolarity Damping Factor Attenuation & Gain SettingOutput Connections Long Speaker Lines Cooling SystemAppendix a Technical Specifications TA-500 TA-500t TA-500H TA-500HMTA-500DP TA-500tDP TA-500HDP Appendix B Spare Parts List Stock Code Model DescriptionAppendix C Warranty TA-500

Related manuals

Manual 73 pages 47.45 Kb