Turbosound TA-500DP, TA-500TDP Attaching the Tilt Straps, Biscuit slides into lower cabinet

Page 33

user manual

TA-500

Figure 9: Biscuit slides into lower cabinet

Attaching the Tilt Straps

When all cabinets have been linked and the top chains attached, the tilt straps can now be attached.

First attach the longer strap to the flybar by sliding the flat buckle into the tilt strap attachment point. Slide the flat buckle on the shorter strap into the tilt strap point on the bottom of the cabinet, insert the free end of the strap through the centre of the ratchet spindle, and pull to apply some tension before ratcheting the column.

WARNING

The tilt strap is designed to ratchet in both directions, an improvement over previous versions which did not allow incremental tilt reduction. However, at all times please note that if the tension on the strap is released suddenly, the column of enclosures may tend to swing violently forwards and care must be taken to avoid danger to persons in the vicinity. It is essential to check that nobody is standing immediately in front of the column, and to give a suitable warning, before the strap is released. Ideally, two persons should support the row from the side whilst the strap is released, or alternatively the bottom row may be returned to the ground before release. In any event it is essential that all personnel in the vicinity are aware that the system is about to move and that they must keep clear.

SAFETY NOTE: Turbosound flying systems have been designed and constructed to a high standard of safety and tested to the most demanding of specifications with a high safety factor. However, anyone involved in flying

ANY sound system, especially in a touring capacity, should take note of the following advice: The rigging of a flown sound system may be dangerous unless undertaken by qualified personnel with the required experience to perform the necessary tasks. Fixing of hanging points in a roof should always be carried out by a professional rigger and in accordance with the local rules of the venue. The house rigger and/or building manager must always be consulted.

TA-500 user manual

Page 33

Image 33

Contents Aspect TA-500 Systems TA-500 TA-500 TA-500 Audio Connections & Controls TA-500HDP EC Declaration of ConformityTurbosound Aspect System Concepts IntroductionAspect Polyhorn Concept TA-880 TA-500 Narrow 25º horizontal coverage Loudspeaker Management System LMS Concept LMS-D2X Loudspeaker Management SystemsNetwork Capability Self-powered Loudspeakers Power AmplifiersDigital Controllers Aspect Loudspeaker ComponentsTA-500 TA-500tDP Self-powered Touring Three-way Loudspeaker TA-500DP Self-powered Three-way LoudspeakerTA-500 Three-way Loudspeaker TA-500t Touring Three-way LoudspeakerTA-500H Horizontal Three-way Loudspeaker TA-500HDP Self-powered Horizontal Three-way LoudspeakerTA-500HM Two-way High/Mid Loudspeaker TSW-218 SubwooferB18 Subwoofer B18DP Self-powered SubwooferTransportation Overview Flying and StackingSafety Notes on Rigging Secondary Safeties Safety InspectionsTA-500 Sample Certificate of Load Test Aspect TA-500 Flying Systems Flying HardwareHorizontal Coverage Vertical CoverageFlybar Settings TA-500T Touring Flying SystemTouring two-wide flybar TOP View FC-500T Flying Chains Flying MatrixTA-500 Integral Flying Hardware TS-890 Tilting StrapsCaptive Biscuit BoltLocking Mechanism Connecting Flying Chains to the CabinetSliding the top chain profile into the slot Assembly of the Top Chains to the CabinetAdding additional rows Connection of additional rowsAttaching the biscuit Setting the angles between rowsBiscuit slides into lower cabinet Attaching the Tilt StrapsFront view of the assembled cluster Lifting the columnTA-500 TA-500 Install Flying System Rigging Instructions TA-500 TA-500 Array is now ready to pick up Flying a single TA-500 cabinet using M10 eyebolts LMS Series Loudspeaker Management Systems Mechanical InstallationIntroduction UnpackingLMS-D24 and D26 Loudspeaker Management Systems FeaturesLCD Front Panel FunctionsTA-500 Rear Panel Functions Selecting a Factory Preset Operating the LMS-D24 and D26 Starting upCreating a Crossover Navigation and Viewing Parameters EQ1 100Hz 0dBNavigation Out1 Freq Width Gain EQ1 100Hz 1.4Q 0.0dBPreset Recall PresetsStore My System Preset StoreDSP Processing Layout Input DSP block diagram Output DSP block diagramStereo / Mono Formats DSP processing Input Channels A Delay 1.50msA Freq Shape Parametric Equalisation High and Low shelving filtersParametric filters Output Channels Gain and Polarity DelayHigh and Low Pass Filters Out1 Freq Shape LPF 2.50k LR24Out1 Freq Slope Gain EQ- 100Hz 12dB 0.0dB Routing LimitersUtilities Utility functions General Features & Facilities T-45 High Efficiency Audio Power AmplifiersFront Panel Functions T-25 Front Panel Functions T-45 Mains Power Powering UpSafety Earthing Voltage Setting Voltage RangeAudio Connections & Controls Gain and Sensitivity Settings PolarityInput Impedance Attenuation & Gain Setting Output ConnectionsDamping Factor Cooling System Long Speaker LinesTA-500 TA-500t TA-500H TA-500HM Appendix a Technical SpecificationsTA-500DP TA-500tDP TA-500HDP Stock Code Model Description Appendix B Spare Parts ListAppendix C Warranty TA-500

Related manuals

Manual 73 pages 47.45 Kb