Turbosound TA-500TDP, TA-500HDP Setting the angles between rows, Attaching the biscuit

Page 32

user manual

TA-500

The lower link must fit into the flygear in a specific way to ensure the reinforcing part bears on the flygear appropriately:

the link must be inserted correctly. Make sure that when using the 21° position the link is fitted parallel to the cabinet side.

Figure 7: Lower link positioning looking from bottom of cabinet

Setting the angles between rows

The setting of the angles between the rows is easily achieved by selecting the desired hole in the index link relating the angle:

Figure 8: Index link angle setting

Attaching the biscuit

Once the inter-cabinet chains have been connected both sides, the captive biscuit must be engaged. To do this, the biscuit is pushed out of its holder in the upper cabinet into the upper kelping bracket of the lower cabinet:

TA-500 user manual

Page 32

Image 32

Contents Aspect TA-500 Systems TA-500 TA-500 TA-500 Audio Connections & Controls EC Declaration of Conformity TA-500HDPIntroduction Turbosound Aspect System ConceptsAspect Polyhorn Concept TA-880 TA-500 Narrow 25º horizontal coverage Network Capability Loudspeaker Management System LMS ConceptLMS-D2X Loudspeaker Management Systems Power Amplifiers Self-powered LoudspeakersDigital Controllers Aspect Loudspeaker ComponentsTA-500 TA-500DP Self-powered Three-way Loudspeaker TA-500tDP Self-powered Touring Three-way LoudspeakerTA-500 Three-way Loudspeaker TA-500t Touring Three-way LoudspeakerTA-500HDP Self-powered Horizontal Three-way Loudspeaker TA-500H Horizontal Three-way LoudspeakerTA-500HM Two-way High/Mid Loudspeaker TSW-218 SubwooferB18DP Self-powered Subwoofer B18 SubwooferTransportation Flying and Stacking OverviewSafety Notes on Rigging Safety Inspections Secondary SafetiesTA-500 Sample Certificate of Load Test Flying Hardware Aspect TA-500 Flying SystemsHorizontal Coverage Vertical CoverageTouring two-wide flybar Flybar SettingsTA-500T Touring Flying System TOP View Flying Matrix FC-500T Flying ChainsTA-500 TS-890 Tilting Straps Integral Flying HardwareBolt Captive BiscuitConnecting Flying Chains to the Cabinet Locking MechanismAssembly of the Top Chains to the Cabinet Sliding the top chain profile into the slotConnection of additional rows Adding additional rowsSetting the angles between rows Attaching the biscuitAttaching the Tilt Straps Biscuit slides into lower cabinetLifting the column Front view of the assembled clusterTA-500 TA-500 Install Flying System Rigging Instructions TA-500 TA-500 Array is now ready to pick up Flying a single TA-500 cabinet using M10 eyebolts Mechanical Installation LMS Series Loudspeaker Management SystemsIntroduction UnpackingFeatures LMS-D24 and D26 Loudspeaker Management SystemsFront Panel Functions LCDTA-500 Rear Panel Functions Creating a Crossover Selecting a Factory PresetOperating the LMS-D24 and D26 Starting up EQ1 100Hz 0dB Navigation and Viewing ParametersOut1 Freq Width Gain EQ1 100Hz 1.4Q 0.0dB NavigationPresets Preset RecallPreset Store Store My SystemStereo / Mono Formats DSP Processing Layout Input DSP block diagramOutput DSP block diagram A Delay 1.50ms DSP processing Input ChannelsA Freq Shape Parametric filters Parametric EqualisationHigh and Low shelving filters Delay Output Channels Gain and PolarityOut1 Freq Shape LPF 2.50k LR24 High and Low Pass FiltersOut1 Freq Slope Gain EQ- 100Hz 12dB 0.0dB Limiters RoutingUtilities Utility functions T-45 High Efficiency Audio Power Amplifiers General Features & FacilitiesFront Panel Functions T-25 Front Panel Functions T-45 Safety Earthing Mains PowerPowering Up Audio Connections & Controls Voltage SettingVoltage Range Input Impedance Gain and Sensitivity SettingsPolarity Damping Factor Attenuation & Gain SettingOutput Connections Long Speaker Lines Cooling SystemAppendix a Technical Specifications TA-500 TA-500t TA-500H TA-500HMTA-500DP TA-500tDP TA-500HDP Appendix B Spare Parts List Stock Code Model DescriptionAppendix C Warranty TA-500

Related manuals

Manual 73 pages 47.45 Kb