Turbosound LMS-D24, LMS-D26 user manual LMS-D6 Rear Panel Functions, Mains Power

Page 49

user manual

TA-890

LMS-D6 Rear Panel Functions

RS232

DATA INPUT

PROTECTION AGAINST FIRE REPLACE ONLY WITH THE SAME TYPE T1A, 250V FUSE

WARNING / AVIS

DO NOT EXPOSE TO RA IN OR MOIST URE THIS EQUIPMENT MUST BE EARTHED SHOCK HAZARD – DO NOT REMOVE COVERS

RISQUE DE CHOC ELECTRIQUE - NE PAS OUVRIR

CUSTOM MADE FOR TURBOSOUND INTHE UK BY XTA ELECTRONICS

OUTPUT 6	OUTPUT 5	OUTPUT 4	OUTPUT 3	OUTPUT 2	OUTPUT 1	INPUT B	INPUT A

PIN1=SHIELD

PIN2=HOT

PIN3=COLD

1

2

3

4

5

1.Power Switch.

2.Mains Fuse - Located in a finger-proof fuseholder adjacent to the mains inlet. Always replace this fuse with the correct type as shown on the rear panel legend. (N.B. A spare fuse is located in this holder.)

3.Mains Power - Connected via a standard IEC socket. A compatible power cord is supplied with the unit.

4.External - RS232 via a 9-pin DIN DEE socket, for connection to a PC.

5.XLR Inputs and Outputs - 3 pin XLR connectors are provided for each audio input and output. All terminations are fully balanced, pin 2 Hot, pin 3 Cold and pin 1 not connected.

Mains Power

The LMS-D6 must always be connected to a 3 wire grounded AC supply. It is supplied with a standard IEC power cord with conductors as follows:

BROWN	Power line Live (Phase)
BLUE	Power line Neutral
GREEN/YELLOW	Safety Earth and ground connection

Units supplied to the North American market are fitted with an integral moulded 3 pin connector, which is provided to satisfy UL & CSA safety standards.

TA-890 user manual Page 49

Image 49

Contents Aspect TA-890 System TA-890 TA-890 TA-890 Amplifier Rack Signal Wiring Output Connections Products EC Declaration of ConformityTurbosound Aspect System Concepts IntroductionTurbosound Polyhorn TA-890 Aspect TA-890 Turnkey System Concept Loudspeaker Management System LMS Concept Power AmplifiersLMS-D24, LMS-D26 and LMS-D6 Loudspeaker Management Systems Amplifier RacksAspect Loudspeaker Components Digital ControllersTA-890L Low Frequency Enclosure TA-890H Mid-high Enclosure TSW-218 SubwooferTA-890 Transportation Aspect Flying Systems Overview Flying and StackingGigmate Acoustic Simulation Setting up a Venue OverviewRunning Turbosound GigMate / Ease Focus for the first time System Setup Designing a system TA-890 TA-890 Changing the system Theatre-style venue 3-wide flown cluster @ 1kHz Safety Notes on Rigging Sample Certificate of Load Test Flying Hardware Wide and Narrow Flybar SettingsSingle A-System Flybar FB-890/1A TOP View Bottom View Figue 3. Triple ‘A’ System Flybar FB-890A/3W TS-890 Tilting Straps FC-890 Flying ChainsTA-890 Four-wide hang using MB-890 and FB-890/2A ‘A’ System Flygear Integral Flying HardwareConnecting Cabinets ‘A’ System Connecting Flying Chains to the CabinetDrop Link Swing LatchSetting Vertical Angles ‘A’ System Attach buckle Attaching the Tilt StrapsBass Enclosure arraying Turbobass DirectivityAiming directivity of the stack TA-890 ABC DEF Typical Left to Right problemBass in a line Creating Directional Bass arraysFanned bass General observations of long lines of bass Bessel ArrayEnd firing array Summing up Ground stacking Mechanical Installation General features & facilities UnpackingLMS Series Loudspeaker Management Systems IntroductionLMS-D6 Front Panel Functions LMS-D6 Rear Panel Functions Mains PowerSafety Earthing Voltage SettingAC Power Fusing Powering UpTime correction for loudspeaker driver placement Input and Output Connector WiringAudio Connections LMS-D24 and D26 Loudspeaker Management Systems FeaturesFront Panel Functions TA-890 Rear Panel Functions Operating the LMS-D24 and D26 Selecting a Factory PresetStarting up Creating a CrossoverNavigation and Viewing Parameters A Freq Width Gain EQ1 100Hz 1.4Q 0.0dBNavigation Out1 Freq Width Gain EQ1 100Hz 1.4Q 0.0dBPresets Preset RecallPreset Store Preset Name Store My SystemOutput DSP block diagram Input DSP block diagramDSP Processing Layout Stereo / Mono FormatsInput Channels DSP ProcessingA Freq Shape HPF 20.0Hz LR24 High and Low shelving filters Parametric EqualisationParametric filters Output Channels DelayGain and Polarity High and Low Pass Filters Out1 Freq Shape LPF 2.50k LR24Out1 Freq Slope Gain EQ- 100Hz 12dB 0.0dB Routing LimitersUtility functions UtilitiesAudio Input Connectors Racking, Cables and Connections AMP-890 Aspect System Amplification RackInput Connections OptionsOutput Connections Amplifier Rack Signal WiringMid-High Outputs Break-out Cables NL4 bass Extension Cables Break-out cables NL8 mid-highMains Connections General Features & Facilities T-45 High Efficiency Audio Power AmplifiersFront Panel Functions T-25 Front Panel Functions T-45 Mechanical Installation Audio Connections & Controls Voltage RangePolarity Gain and Sensitivity SettingsInput Impedance Damping Factor Attenuation & Gain SettingCooling System Long Speaker LinesMaintenance To rotate the horn moulding from ‘A’ mode to ‘B’ mode Removal of the high frequency driver To rotate the horn moulding from ‘B’ mode to ‘A’ modeRemoval of the high-mid frequency driver Removal of the low-mid frequency drive units General MaintenancePaintwork TA-890 Technical Specifications Serial Numbers WarrantyTA-890